Timing Belt Pulley 30 HTD-8M/24-2 with taper-lock - Taper-lock 1108

Timing Belt Pulley 30 HTD-8M/24-2 with taper-lock - Taper-lock 1108

When a timing belt pulley needs to be replaced, the small details are often the most important. Here, the taper-lock number, number of teeth, belt width and shaft area are therefore combined in the text, so that the product can be checked without guessing. Timing Belt Pulley 30 HTD-8M/24-2 with taper-lock - Taper-lock 1108 is an HTD 8M timing belt pulley for synchronous power transmission with taper-lock system. The pulley has 24 teeth, is designed for a 30 mm wide HTD 8M timing belt and uses taper bushing 1108. With the appropriate taper bushing, the shaft area covers Ø9-28 mm. This makes the product relevant when a standardized solution is desired, where the pulley can be mounted on several different shaft diameters without having to be specially drilled first. The taper bushing itself is selected according to the shaft diameter and is usually ordered separately, unless otherwise stated in the order.

HTD 8M is a metric timing belt profile with 8 mm pitch and a rounded tooth shape, which is developed for positive engagement between the timing belt and timing belt pulley . In practice, this means that the belt does not work on friction alone, but transfers torque via the tooth engagement. This is an important difference compared to a regular V-belt drive, because the position, pitch and tooth profile of the belt must match exactly. Therefore, an HTD 8M pulley must always be combined with an HTD 8M belt of the correct width and length. 30 mm belt width is a widely used intermediate size for machine construction, service tasks and replacement parts, where the load is higher than with the narrowest belts, but where the space must still be used sensibly.

Technical specifications of the pulley

The dimensions in this description are written from the supplier's technical data for the HTD 8M taper timing belt pulley in the specified belt width. The most important dimensions for this variant are collected here so that the item can be compared with a drawing, spare parts list or existing component. Pay particular attention to the taper-lock number, as the tapered hub of the pulley must fit the correct bushing type. For example, a taper bushing 1008 cannot be replaced by a 1615 or 2012, even though the shaft diameter may seem close. It is the hub taper itself, the length of the bushing and the screw location that determine compatibility.

• Profile: HTD 8M with 8 mm metric pitch
• Number of teeth: 24
• Belt width: 30 mm
• Version: 16F
• Taper-lock / taper bushing: 1108
• Shaft range with suitable taper bushing: Ø9-28 mm
• Outer diameter: 59.74 mm
• Pitch Diameter: 61.12 mm
• Flange Diameter (FD): 66 mm
• Total width (w): 38 mm
• L-dimension: 22 mm
• R-dimension: 16 mm
• Material: phosphated steel
• Weight: approx. 0.400 kg

The outside diameter is 59.74 mm, while the Pitch Diameter is 61.12 mm. The Pitch Diameter is the theoretical pitch diameter used when calculating gear ratio, belt speed, and center distance. The outside diameter, on the other hand, is the physical outer dimension of the pulley above the tooth tip. Both measurements can be relevant, but they are not used for the same purpose. If you are replacing an existing pulley, the number of teeth and profile should always be given more weight than simply measuring the outside diameter with a caliper.

Taper-lock 1108 and shaft range Ø9-28 mm

This pulley is prepared for taper-lock / taper bushing 1108. The taper bushing acts as a conical clamping bushing between the shaft and the pulley hub. The advantage is that the same timing belt pulley can be used on several shaft diameters, as long as the bushing is the right type and has the correct bore for the shaft. For this variant, the relevant shaft range is Ø9-28 mm. This does not mean that the pulley itself has a continuous cylindrical bore in all these sizes; it means that the pulley fits with a taper bushing 1108, which is available in different bores within the specified range.

If the pulley is to be part of a new belt drive, the dimensioning should always be seen together with the center distance, speed, load, belt type and the opposite timing belt pulley . The item itself here describes the pulley's dimensions and compatible taper bushing, so it is easier to choose correctly. When errors occur with taper-lock products, it is often because the taper bushing in the product name, short description and technical text do not match. In this updated text, the taper-lock number is therefore stated in several places and written into the product name, so that it can also be clearly seen when processing orders. For this item, the correct taper bushing is 1108. If a taper bushing is already on the machine, the number on the bushing should be checked physically before reusing it.

Belt width, number of teeth and application

The pulley is designed for HTD 8M timing belts with a belt width of 30 mm. The belt width must fit the belt, but it must also fit the load and safety factor chosen in the design. A wider belt drive can typically transmit more torque than a narrow belt drive, but also requires more space and correct alignment. This variant has 24 teeth, which gives a Pitch Diameter of 61.12 mm. It is the number of teeth that, together with the opposing pulley, determines the gear ratio in the belt drive.

The relatively low number of teeth results in a compact pulley, which is relevant when the pulleybase is limited or when a smaller pulley diameter is desired. Smaller pulleys should always be checked against the recommended minimum belt diameter and the specific load. If the pulley is used as a replacement for an existing timing belt pulley , the belt profile, number of teeth, belt width and taper-lock type should be checked before ordering. If used in a new construction, the selection should be made in conjunction with calculations of the center distance, meshing ratio, load, starting torque, ambient temperature and any noise or maintenance requirements. The product here describes the timing belt pulley itself; the final dimensioning of the entire belt drive depends on the machine.

Material and workmanship

This variant is made of phosphated steel. The choice of material follows the number of teeth and size: variants up to and including 72 teeth are usually in phosphated steel, while larger variants from 80 teeth and upwards are in phosphated GG25 cast iron. The phosphated surface gives an industrial standard look and helps protect the surface during normal handling and splice. However, this does not change the fact that the pulley must still be stored dry and assembled correctly, especially if it is to be used in an environment with moisture, dust or frequent cleaning.

The design/version for this item is 16F. The version describes the pulley geometry in the supplier's drawing, including the relationship between hub, b-dimension, L-dimension, R-dimension and any flange. Total width (b) is 38 mm, L-dimension is 22 mm, and R-dimension is 16 mm. The pulley has a specified flange diameter of 66 mm. The flange/plate helps to guide the belt laterally, but correct alignment between the pulleys is still necessary because a timing belt should not run constantly against the edge. If you are comparing with an existing pulley, you should therefore not only look at the number of teeth and belt width, but also at the hub length and the dimensions that determine the location on the shaft.

Splice and practical check

Always check that the bushing is correctly positioned in the cone before tightening the screws. The Taper-lock system works by clamping the bushing around the shaft, and therefore correct cleaning, positioning and re-tensioning are important for stable operation. The Taper-lock system makes splice and dissplice easier than a fixed machined hub bore, but it still requires correct operation. Screws, cone surfaces and shaft must be clean. The bushing must not be forced into place with impact, and the pulley should not be tightened until it is aligned with the other timing belt pulley . After a short run-in, it may be relevant to check the tension again, especially in systems where the load varies or where the machine runs many times a day.

A timing belt with HTD 8M profile must run cleanly in the tooth groove. If the belt wanders to the side, becomes hot, makes noise or shows uneven wear, it is rarely the tooth profile itself that is the cause. Check the parallelism between shafts, the flatness between the pulleys, the correct belt tension and whether the on-board pulleys/flanges affect the belt. Too high a belt tension can strain bearings and shafts, while too low a belt tension can cause tooth skipping during acceleration or shock loading.

When does this timing belt pulley fit?

This item is suitable when you need a HTD 8M timing belt pulley with 24 teeth, 30 mm belt width and taper-lock 1108. It will not automatically fit just because the outer diameter is close to an existing pulley. The correct check is: same profile, same number of teeth, suitable belt width, correct taper bushing and compatible shaft dimensions. If the machine uses a different tooth profile, for example T10, AT10, RPP or another HTD pitch, a different type of pulley must be selected.

Check before ordering

First check the marking or dimensions of the existing timing belt. Then check the number of teeth on the pulley, belt width and taper-lock number. For this item, the key data is: 24 teeth, 30 mm belt width, taper-lock 1108, shaft range Ø9-28 mm and material Steel. If you also need to use the taper bushing, it must be selected in the same taper-lock type and with the specific shaft bore that fits the machine. This way you avoid ordering the correct pulley with the wrong bushing.