Timing Belt Pulley 85 HTD-8M/48-2 with taper-lock - Taper-lock 2517

Timing Belt Pulley 85 HTD-8M/48-2 with taper-lock - Taper-lock 2517

This timing belt pulley is designed for the practical situation where you need to find a pulley that fits both the belt and the shaft in the machine. Timing Belt Pulley 85 HTD-8M/48-2 with taper-lock - Taper-lock 2517 is an HTD 8M timing belt pulley/ timing belt pulley for synchronous power transmission with taper-lock system. The pulley has 48 teeth, is designed for an 85 mm wide HTD 8M timing belt and uses taper bushing 2517. With the appropriate taper bushing, the shaft range covers Ø15-65 mm. This makes the product relevant when a standardized solution is desired, where the pulley can be mounted on several different shaft diameters without having to be specially drilled first. The taper bushing itself is selected according to the shaft diameter and is usually ordered separately, unless otherwise stated in the order.

HTD 8M is a metric timing belt profile with 8 mm pitch and a rounded tooth shape, which is developed for positive engagement between the timing belt and timing belt pulley . In practice, this means that the belt does not work on friction alone, but transfers torque via the tooth engagement. This is an important difference compared to a regular V-belt drive, because the position, pitch and tooth profile of the belt must match exactly. Therefore, an HTD 8M pulley must always be combined with an HTD 8M belt of the correct width and length. 85 mm belt width is a powerful solution for wide HTD 8M belts, where the tooth engagement and contact surface must be able to handle a higher torque and a more loaded machine task.

Technical specifications of the pulley

The dimensions in this description are written from the supplier's technical data for the HTD 8M taper timing belt pulley in the specified belt width. The most important dimensions for this variant are collected here so that the item can be compared with a drawing, spare parts list or existing component. Pay particular attention to the taper-lock number, as the tapered hub of the pulley must fit the correct bushing type. For example, a taper bushing 1008 cannot be replaced by a 1615 or 2012, even though the shaft diameter may seem close. It is the hub taper itself, the length of the bushing and the screw location that determine compatibility.

• Profile: HTD 8M with 8 mm metric pitch
• Number of teeth: 48
• Belt width: 85 mm
• Version: 18F
• Taper-lock / taper bushing: 2517
• Shaft range with suitable taper bushing: Ø15-65 mm
• Outer diameter: 120.86 mm
• Pitch Diameter: 122.23 mm
• Flange Diameter (FD): 127 mm
• Total width (w): 95 mm
• L-dimension: 45 mm
• R-dimension: 25.0 mm
• Material: phosphated steel
• Weight: approximately 2.66 kg

The outside diameter is 120.86 mm, while the Pitch Diameter is 122.23 mm. The Pitch Diameter is the theoretical pitch diameter used when calculating gear ratio, belt speed, and center distance. The outside diameter, on the other hand, is the physical outer dimension of the pulley above the tooth tip. Both measurements can be relevant, but they are not used for the same purpose. If you are replacing an existing pulley, the number of teeth and profile should always be given more weight than simply measuring the outside diameter with a caliper.

Taper-lock 2517 and shaft range Ø15-65 mm

This pulley is prepared for taper-lock / taper bushing 2517. The taper bushing acts as a conical clamping bushing between the shaft and the pulley hub. The advantage is that the same timing belt pulley can be used on several shaft diameters, as long as the bushing is the right type and has the correct bore for the shaft. For this variant, the relevant shaft range is Ø15-65 mm. This does not mean that the pulley itself has a continuous cylindrical bore in all these sizes; it means that the pulley fits with a taper bushing 2517, which is available in different bores within the specified range.

When a pulley is selected for an existing machine, the number of teeth, belt width, taper bushing and the geometric dimensions of the pulley in particular must be checked. An apparently small difference in the taper-lock number can mean that the bushing the customer has in stock does not fit in the hub. When errors occur with taper-lock products, it is often because the taper bushing in the product name, short description and technical text do not match. In this updated text, the taper-lock number is therefore stated in several places and written into the product name so that it can also be clearly seen when processing orders. For this item, the correct taper bushing is 2517. If a taper bushing is already on the machine, the number on the bushing should be checked physically before reusing it.

Belt width, number of teeth and application

The pulley is designed for HTD 8M timing belts with a belt width of 85 mm. The belt width must fit the belt, but it must also fit the load and safety factor chosen in the design. A wider belt drive can typically transmit more torque than a narrow belt drive, but also requires more space and correct alignment. This variant has 48 teeth, which gives a Pitch Diameter of 122.23 mm. It is the number of teeth that, together with the opposing pulley, determines the gear ratio in the belt drive.

The number of teeth is in a range where the pulley is often used as a standard pulley in common machine designs. This provides a reasonable balance between diameter, tooth engagement and space requirement in the design. If the pulley is used as a replacement for an existing timing belt pulley , the belt profile, number of teeth, belt width and taper-lock type should be checked before ordering. If used in a new design, the selection should be made in conjunction with calculations of centre distance, engagement number, load, starting torque, ambient temperature and any noise or maintenance requirements. The product here describes the timing belt pulley itself; the final dimensioning of the entire belt drive depends on the machine.

Material and workmanship

This variant is made of phosphated steel. The choice of material follows the number of teeth and size: variants up to and including 72 teeth are usually in phosphated steel, while larger variants from 80 teeth and upwards are in phosphated GG25 cast iron. The phosphated surface gives an industrial standard look and helps protect the surface during normal handling and splice. However, this does not change the fact that the pulley must still be stored dry and assembled correctly, especially if it is to be used in an environment with moisture, dust or frequent cleaning.

The design/version for this item is 18F. The version describes the pulley geometry in the supplier's drawing, including the relationship between hub, b-dimension, L-dimension, R-dimension and any flange. Total width (b) is 95 mm, L-dimension is 45 mm, and R-dimension is 25.0 mm. The pulley has a specified flange diameter of 127 mm. The flange/plate helps to guide the belt laterally, but correct alignment between the pulleys is still necessary because a timing belt should not run constantly against the edge. If you are comparing to an existing pulley, you should therefore not only look at the number of teeth and belt width, but also at the hub length and the dimensions that determine the location on the shaft.

Splice and practical check

Always check that the bushing is correctly positioned in the cone before tightening the screws. The Taper-lock system works by clamping the bushing around the shaft, and therefore correct cleaning, positioning and re-tensioning are important for stable operation. The Taper-lock system makes splice and dissplice easier than a fixed machined hub bore, but it still requires correct operation. Screws, cone surfaces and shaft must be clean. The bushing must not be forced into place with impact, and the pulley should not be tightened until it is aligned with the other timing belt pulley . After a short run-in, it may be relevant to check the tension again, especially in systems where the load varies or where the machine runs many times a day.

A timing belt with HTD 8M profile must run cleanly in the tooth groove. If the belt wanders to the side, becomes hot, makes noise or shows uneven wear, it is rarely the tooth profile itself that is the cause. Check the parallelism between shafts, the flatness between the pulleys, the correct belt tension and whether the on-board pulleys/flanges affect the belt. Too high a belt tension can strain bearings and shafts, while too low a belt tension can cause tooth skipping during acceleration or shock loading.

When does this timing belt pulley fit?

This item is suitable when you need a HTD 8M timing belt pulley with 48 teeth, 85 mm belt width and taper-lock 2517. It does not automatically fit just because the outer diameter is close to an existing pulley. The correct check is: same profile, same number of teeth, suitable belt width, correct taper bushing and compatible shaft dimensions. If the machine uses a different tooth profile, for example T10, AT10, RPP or another HTD pitch, a different type of pulley must be selected.

Check before ordering

First check the marking or dimensions of the existing timing belt. Then check the number of teeth on the pulley, belt width and taper-lock number. For this item, the key data is: 48 teeth, 85 mm belt width, taper-lock 2517, shaft range Ø15-65 mm and material Steel. If you also need to use the taper bushing, it must be selected in the same taper-lock type and with the specific shaft bore that fits the machine. This way you avoid ordering the correct pulley with the wrong bushing.