V-belt XPC 2360 - 22x18MM - PIX X'tra ®

V-belt XPC 2360 - 22x18 MM - PIX X'tra ® - timing rough-edged XPC V-belt with Ld 2360 mm

V-belt XPC 2360 - 22x18 MM - PIX X'tra ® is developed for V-shaped belt drives, where the sides of the belt work against the pulley grooves. The timing PIX X'tra® construction makes the belt flexible around the pulley, and the data given can be compared to a belt's technical specification: profile XPC, goal 22x18MM, Ld 2360mm, Li 2277mm and La 2390mm.

XPC is the largest profile in this XP series and is typically used in more demanding belt drives, where a wider and taller V-belt is required. The belt is particularly relevant for heavy belt drives, larger machines and installations, where the belt must have a large contact surface and high stability. The correct cross-section is essential for the sides of the belt to grip the pulley properly and be able to transfer the torque without unnecessary slip.

Product data

• Profile: XPC
• Goal: 22x18MM
• Effective length: Length 2360 mm
• Inner length: 2277 mm
• External length: Width 2390 mm
• Series: PIX X'tra® Molded Raw Edge Cogged Belts
• Construction: raw edge and Cogged V-belts
• Profile angle according to PIX data sheet: 38° ± 1°
• Mark: PIX

Length specifications

The Ld dimension is the effective length and the length specification typically used for narrow V-belts. Li describes the inner length, while La describes the outer length. The three dimensions must be understood together with the profile, cross-section and pulley grooves, because the length designation alone does not describe the full geometry of the belt.

The three length specifications describe the belt's geometry from each measurement position. 2277 mm describes the inner length, Length 2360 mm is the effective length, and Width 2390 mm is the outer length. The difference between them is due to the geometry of the belt and the measurement method. Therefore, belts with almost the same outer dimensions can still have different technical specifications.

With Ld 2360 mm, the belt is a longer variant, where alignment and uniform tension are more important. The longer the center distance and the greater the belt pull, the more important it is that the belt does not work crookedly between the pulleys.

Construction and technical features of PIX X'tra®

The raw edge construction means that the sides of the belt are designed for direct contact with the pulley. The serrated underside makes the belt more compliant around pulleys, especially where the diameter is limited. PIX also specifies polyester cord as a tensile member, which is relevant for longitudinal stability and load capacity in a correctly dimensioned belt drive.

PIX states for the X'tra® series a power transmission capacity of 15–20% over wrapped belts in comparable operating conditions. The data sheet also highlights better flexibility, approximately 20% higher heat dissipation than wrapped belts, possibility of smaller pulleys in compact drives, maximum linear belt speed up to 42 m/s, antistatic design, oil and heat resistance, REACH/RoHS compliance and temperature range from -45°C to +120°C.

For the XPC profile, the PIX data sheet states the length range 600–8380 mm. This belt with Ld 2360 mm is in the range 600–3000 mm, where the data sheet states a length tolerance of ±6 mm and a set tolerance of 2 mm. The tolerances are relevant when replacing, especially if several belts are to run in parallel or if the center distance can only be adjusted to a limited extent.

Use for the XPC profile

This XPC belt is relevant in heavy duty applications with larger pulleys, longer center distances or higher power transmission requirements. In operation, the pulley groove, belt cross-section and timing construction affect the contact between belt and pulley. Profile and length must match, as correct length does not compensate for incorrect cross-section.

The operating situation has a great impact on the belt's lifespan: is the belt running constantly, are there many starts/stops, is the load even, and are the pulleys clean and in good condition? This XPC belt is designed for mechanical power transmission, but lifespan and operation still depend on alignment, tension, temperature, pulley quality, and whether the belt is installed without damage.

Profile and pulley compatibility

XPC belongs to the same narrow profile family as SPC, but the belt has its own technical specification with a timing, raw-edge construction. The belt works with side contact in the pulley groove, and the correct groove profile is necessary for the contact surface, friction and load to be distributed correctly. Incorrect cross-section or skewed pulleys can cause overheating, noise, slippage and uneven wear.

The technical identification consists of the combination XPC, 22x18MM, Length 2360 mm, 2277 mm, Width 2390 mm and PIX X'tra®The combination distinguishes the item from nearby V-belts with other profiles, other length standards or a different construction.

Installation and operation

When installing, the belt should be placed without being twisted or forced over the pulley with a screwdriver or other sharp tool. Instead, adjust the center distance or loosen the relevant tensioning device so that the belt can be installed without damage. After installation, the belt should have the tension that the machine is designed for, because both too loose and too tight a belt can cause problems.

A new belt should be installed in clean, dry and undamaged pulleys. Oil, old belt dust, rust or sharp edges can shorten the life. Alignment between the pulleys is also important. Even a good belt can quickly wear out if the pulleys are misaligned or if the belt is forced to work sideways.

Avoid using belt spray as a permanent solution to slippage. Slippage is often caused by incorrect tension, worn pulleys, oil contamination or incorrect belt specification. A properly specified XPC belt of the correct length and in a clean, aligned belt drive is a more durable solution than temporary remedies.

In practice, the combination of XPC profile, 22x18 MM and Ld 2360 mm means that the belt works as part of the overall geometry of the belt drive. The rough-edged side surface transfers the force to the pulley, while the teeth on the inside support the flexibility around the pulleys. With correct tension, the belt can work smoothly with a lower risk of heat build-up, slippage and unnecessary wear. The specified Li, Ld and La dimensions also make it clear which measurement line is being described.

For the XPC 2360, a clean and smooth contact between the belt and pulley is an essential part of the overall function. The belt path should be free of oil, sharp edges and accumulated belt dust, as these conditions can affect friction, temperature and wear pattern.

Technical questions about XPC V-belts

What does XPC 2360 mean on this belt?

XPC is the profile designation and 2360 refers to the effective length Ld in millimeters. For this item, this means that the belt is specified as an XPC profile with dimensions 22x18 MM, Li 2277 mm, Ld 2360 mm and La 2390 mm.

Is PIX X'tra® a regular wrapped V-belt?

No. The PIX X'tra® in this series is a moulded raw edge cogged belt. It differs from classic wrapped belts in construction, flexibility and working surface.

When should the belt be replaced?

The belt should be replaced if there are ctiming bars, obvious side surface wear, frayed edges, glazing, squealing, vibrations or repeated retensioning. The pulleys should also be in good condition, as a new belt will wear quickly in damaged grooves.

Do all belts need to be replaced if there are several next to each other?

Yes, in parallel belt drives it is usually best to replace the entire set. Mixing belts of different ages or levels of wear can cause the load to be unevenly distributed, causing one belt to work harder than the others.

Can the belt be used in hot or oily environments?

PIX lists the series as heat and oil resistant, but this does not mean that the belt should run in constant oil contamination or without control of the operating environment. Cleaning, shielding and correct sizing are still important.

What does antistatic performance mean?

Antistatic design means that the belt is designed to reduce static charge under suitable conditions. In specific environments, the final suitability depends on the requirements of the entire plant and relevant approvals.

Belt operation depends on the profile, length, tension and pulley groove matching. Worn or damaged grooves can shorten belt life, while correct alignment and a clean contact surface provide more stable power transmission.

Short conclusion: V-belt XPC 2360 - 22x18 MM - PIX X'tra ® is an XPC V-belt from PIX X'tra® with dimensions 22x18 MM, Ld 2360 mm, Li 2277 mm and La 2390 mm. It is a relevant belt type when the belt drive requires this particular profile and a rough-edged, timing construction with the technical properties that PIX specifies for the X'tra® series.