V-belt XPZ 1090 - 10x8 MM - PIX X'tra ®

V-belt XPZ 1090 - 10x8 MM - PIX X'tra ® – PIX X'tra® narrow V-belt for stable power transmission

V-belt XPZ 1090 - 10x8 MM - PIX X'tra ® is a raw edged and Cogged V-belts from the PIX X'tra® series. It is intended for belt drives where the profile, length and pulley groove must match exactly to ensure stable operation. This variant has profile XPZ, goal 10x8MM, effective length Ld 1090 mm, inside length 1053 mm and external length Width 1103 mm.

XPZ is the lightest profile in the XP series and is typically used when the machine requires a narrow, Cogged V-belts with high flexibility. The belt is particularly relevant for compact belt drives, smaller pulleys and installations where space around the shafts is limited. The correct cross-section is essential for the sides of the belt to grip the pulley properly and be able to transfer the torque without unnecessary slip.

Product data

• Profile: XPZ
• Goal: 10x8MM
• Effective length: Ld 1090 mm
• Inner length: 1053 mm
• External length: Width 1103 mm
• Series: PIX X'tra® Molded Raw Edge Cogged Belts
• Construction: raw edge and Cogged V-belts
• Profile angle according to PIX data sheet: 36° ± 1°
• Mark: PIX

Length specifications

The Ld dimension is the effective length and the length specification typically used for narrow V-belts. Li describes the inner length, while La describes the outer length. The three dimensions must be understood together with the profile, cross-section and pulley grooves, because the length designation alone does not describe the full geometry of the belt.

The three length specifications describe the belt's geometry from each measurement position. 1053 mm describes the inner length, Ld 1090 mm is the effective length, and Width 1103 mm is the outer length. The difference between them is due to the geometry of the belt and the measurement method. Therefore, belts with almost the same outer dimensions can still have different technical specifications.

With Ld 1090 mm, the belt is in a common working range for many machines. Here, it is typically not only the length, but also the condition of the pulleys, center distance and correct tension that determine whether the belt drive runs stably over time.

Construction and technical features of PIX X'tra®

The raw edge construction means that the sides of the belt are designed for direct contact with the pulley. The serrated underside makes the belt more compliant around pulleys, especially where the diameter is limited. PIX also specifies polyester cord as a tensile member, which is relevant for longitudinal stability and load capacity in a correctly dimensioned belt drive.

PIX states for the X'tra® series a power transmission capacity of 15–20% over wrapped belts in comparable operating conditions. The data sheet also highlights better flexibility, approximately 20% higher heat dissipation than wrapped belts, possibility of smaller pulleys in compact drives, maximum linear belt speed up to 42 m/s, antistatic design, oil and heat resistance, REACH/RoHS compliance and temperature range from -45°C to +120°C.

For the XPZ profile, the PIX data sheet states the length range 550–5000 mm. This belt with Ld 1090 mm is in the range 550–3000 mm, where the data sheet states a length tolerance of ±6 mm and a set tolerance of 2 mm. The tolerances are relevant when replacing, especially if several belts are to run in parallel or if the center distance can only be adjusted to a limited extent.

Use for the XPZ profile

The operating situation has a great impact on the belt's lifespan: is the belt running constantly, are there many starts/stops, is the load even, and are the pulleys clean and in good condition? This XPZ belt is designed for mechanical power transmission, but lifespan and operation still depend on alignment, tension, temperature, pulley quality, and whether the belt is installed without damage.

This XPZ belt is relevant in small and medium-sized belt drives, where correct fit and low overall height are more important than a very wide profile. In operation, the pulley groove, the belt cross-section and the timing construction are important for the contact between the belt and pulley. Profile and length must match, as correct length does not compensate for an incorrect cross-section.

Profile and pulley compatibility

XPZ belongs to the same narrow profile family as SPZ, but the belt has its own technical specification with a timing, raw-edge construction. The belt works with side contact in the pulley groove, and the correct groove profile is necessary for the contact surface, friction and load to be distributed correctly. Incorrect cross-section or skewed pulleys can cause overheating, noise, slippage and uneven wear.

The technical identification consists of the combination XPZ, 10x8MM, Ld 1090 mm, 1053 mm, Width 1103 mm and PIX X'tra®The combination distinguishes the item from nearby V-belts with other profiles, other length standards or a different construction.

Installation and operation

When installing, the belt should be placed without being twisted or forced over the pulley with a screwdriver or other sharp tool. Instead, adjust the center distance or loosen the relevant tensioning device so that the belt can be installed without damage. After installation, the belt should have the tension that the machine is designed for, because both too loose and too tight a belt can cause problems.

A new belt should be installed in clean, dry and undamaged pulleys. Oil, old belt dust, rust or sharp edges can shorten the life. Alignment between the pulleys is also important. Even a good belt can quickly wear out if the pulleys are misaligned or if the belt is forced to work sideways.

Avoid using belt spray as a permanent solution to slippage. Slippage is often caused by incorrect tension, worn pulleys, oil contamination or incorrect belt specification. A correctly specified XPZ belt of the correct length and in a clean, aligned belt drive is a more durable solution than temporary remedies.

The XPZ profile with the dimensions 10x8 MM is part of the narrow Cogged V-belts, where the fit of the side surfaces in the pulley groove is crucial for the power transmission. Ld 1090 mm describes the effective length, while Li 1053 mm and La 1103 mm describe the inner and outer measurement line of the belt. Together, the dimensions give a more precise picture of the belt geometry than the length alone. The technical structure is therefore relevant in both new and established belt drives.

The raw edge construction gives the belt direct working surfaces against the pulley. Together with the polyester tension member and the serrated underside, this contributes to a design designed for mechanical power transmission under varying operating conditions.

Technical questions about XPZ V-belts

What does XPZ 1090 mean on this belt?

XPZ is the profile designation and 1090 refers to the effective length Ld in millimeters. For this item, this means that the belt is specified as XPZ profile with dimensions 10x8 MM, Li 1053 mm, Ld 1090 mm and La 1103 mm.

Why does a new V-belt get hot?

Heat is often caused by incorrect tension, misaligned pulleys, worn grooves, excessive load or incorrect profile. A correctly specified belt can still have a short life if the belt drive is not adjusted correctly.

Is external length the same as effective length?

No. La is the external length, while Ld is the effective length. They must not be mixed up because the difference may be enough to prevent the belt from being tensioned correctly.

What conditions affect the operation of the belt?

Profile, dimensions, Ld, Li, La, pulley groove, number of belts in the drive and machine operation all affect the load on the belt. When these conditions match, the belt works more stably and has a longer service life.

What do Ld, Li and La mean on this V-belt?

Ld is the effective length and is the length stated in the product name. Li is the inside length, and La is the outside length. The three measurements are used to compare belts because manufacturers and older belt markings do not always use the same length designation.

Is the length alone enough to describe the belt?

No. The length is important, but the profile is at least as important. A belt with the correct length but the wrong profile can lie incorrectly in the pulley, causing poor contact, heat, noise and a shorter life.

When making technical comparisons, length, profile, cross-section and the product's Li, Ld and La should be viewed together. This makes the difference between internal, effective and external length clear and reduces the risk of confusion between adjacent belt sizes.

Short conclusion: V-belt XPZ 1090 - 10x8 MM - PIX X'tra ® is an XPZ V-belt from PIX X'tra® with dimensions 10x8 MM, Ld 1090 mm, Li 1053 mm and La 1103 mm. It is a relevant belt type when the belt drive requires this particular profile and a rough-edged, timing construction with the technical properties that PIX specifies for the X'tra® series.