V-belt XPZ 655 - 10x8 MM - PIX X'tra ®

V-belt XPZ 655 - 10x8 MM - PIX X'tra ® – correct profile, length and PIX X'tra® construction

V-belt XPZ 655 - 10x8 MM - PIX X'tra ® is a raw edged and Cogged V-belts from the PIX X'tra® series. It is intended for belt drives where the profile, length and pulley groove must match exactly to ensure stable operation. This variant has profile XPZ, goal 10x8MM, effective length Ld 655 mm, inside length 618 mm and external length Width 668 mm.

XPZ is the lightest profile in the XP series and is typically used when the machine requires a narrow, Cogged V-belts with high flexibility. The practical advantage of the correct profile is that the belt should neither bottom out in the groove nor be too high. When the profile fits, the load is better distributed on the sides of the belt and the belt drive has a better chance of running smoothly.

Product data

• Profile: XPZ
• Goal: 10x8MM
• Effective length: Ld 655 mm
• Inner length: 618 mm
• External length: Width 668 mm
• Series: PIX X'tra® Molded Raw Edge Cogged Belts
• Construction: raw edge and Cogged V-belts
• Profile angle according to PIX data sheet: 36° ± 1°
• Mark: PIX

Length specifications

The three length specifications describe the belt's geometry from each measurement position. 618 mm describes the inner length, Ld 655 mm is the effective length, and Width 668 mm is the outer length. The difference between them is due to the geometry of the belt and the measurement method. Therefore, belts with almost the same outer dimensions can still have different technical specifications.

When a belt is specified from an older marking, it is usually best to compare both the letter profile and length designation. A belt marked as XPZ 655 should not be confused with another profile of the same nominal length. Therefore, consider both Li, Ld and La together with the profile and dimensions.

With Ld 655 mm, the belt is in the shorter part of the range. This makes longitudinal stability and correct belt geometry particularly important, because small errors in length or profile can quickly be noticed in a compact belt drive with limited adjustment options.

Construction and technical features of PIX X'tra®

The PIX data sheets describe the construction with a special textile/fabric layer as a cover, a cushion rubber compound around the belt's working area, polyester cord as a tensile member and an EPDM-based compression part. In practice, this means that the belt should not only be assessed on its length. The internal construction is important for strength, flexibility, heat management and stability under load.

The main technical features of the PIX series are the timing flexibility, higher heat dissipation than a classic wrapped belt and the possibility of working in compact belt drives when the rest of the drive is correctly dimensioned. The series is also specified as antistatic, oil and heat resistant and REACH and RoHS compliant. These features are particularly relevant in machines where the belt runs for many times and is not only used occasionally.

For the XPZ profile, the PIX data sheet states the length range 550–5000 mm. This belt with Ld 655 mm is in the range 550–3000 mm, where the data sheet states a length tolerance of ±6 mm and a set tolerance of 2 mm. The tolerances are relevant when replacing, especially if several belts are to run in parallel or if the center distance can only be adjusted to a limited extent.

Use for the XPZ profile

If the machine has previously used a regular wrapped V-belt, a timing raw edge type may be interesting for compact drives or when greater flexibility is needed. This does not mean that all belts can be freely replaced. The safe method is to maintain the same profile family, assess the length and ensure that the pulleys are suitable for the specified belt type.

In practice, this type of belt is often used for compact belt drives, smaller pulleys and installations where space around the shafts is limited. However, the belt should not be selected solely based on the machine type. Two machines can use different profiles, even if they look similar from the outside. The correct check is therefore the product name, belt marking, pulley profile and the three length measurements.

Profile and pulley compatibility

XPZ belongs to the same narrow profile family as SPZ, but the belt has its own technical specification with a timing, raw-edge construction. The belt works with side contact in the pulley groove, and the correct groove profile is necessary for the contact surface, friction and load to be distributed correctly. Incorrect cross-section or skewed pulleys can cause overheating, noise, slippage and uneven wear.

The technical identification consists of the combination XPZ, 10x8MM, Ld 655 mm, 618 mm, Width 668 mm and PIX X'tra®The combination distinguishes the item from nearby V-belts with other profiles, other length standards or a different construction.

Installation and operation

A new belt should be installed in clean, dry and undamaged pulleys. Oil, old belt dust, rust or sharp edges can shorten the life. Alignment between the pulleys is also important. Even a good belt can quickly wear out if the pulleys are misaligned or if the belt is forced to work sideways.

After start-up, it is wise to listen for abnormal noise and feel for abnormal heat when it is safe to do so. Slippage, whining, vibrations or black belt dust may indicate incorrect tension, incorrect profile, worn pulleys or excessive load. The fault should be found before the machine continues to run for a long time.

During continuous operation, the belt should be evaluated for ctiming bars, heavily worn side faces, glazing, frayed edges, and signs of overheating. If the belt repeatedly needs to be retensioned, it is often an indication that either the belt, the pulleys, or the setup itself should be examined. Replacing the belt alone does not always solve the cause of the problem.

As part of the PIX X'tra® series, the belt is designed for industrial belt drives where stable friction, flexibility and length stability must work together. The specified profile angle, the three length dimensions and the timing underside describe different sides of the same construction. For the XPZ 655, this results in a belt that is technically defined by both cross-section and effective length, not just by the nominal length in the product name.

Technical questions about XPZ V-belts

What does XPZ 655 mean on this belt?

XPZ is the profile designation and 655 refers to the effective length Ld in millimeters. For this item, this means that the belt is specified as XPZ profile with dimensions 10x8 MM, Li 618 mm, Ld 655 mm and La 668 mm.

What do Ld, Li and La mean on this V-belt?

Ld is the effective length and is the length stated in the product name. Li is the inside length, and La is the outside length. The three measurements are used to compare belts because manufacturers and older belt markings do not always use the same length designation.

Is the length alone enough to describe the belt?

No. The length is important, but the profile is at least as important. A belt with the correct length but the wrong profile can lie incorrectly in the pulley, causing poor contact, heat, noise and a shorter life.

Why is the belt timing on the inside?

The serration makes the belt more flexible around the pulley and helps with heat dissipation. This is especially relevant for compact belt drives, smaller pulleys and operations where a stiffer wrapped belt can become unnecessarily hot.

Is PIX X'tra® a regular wrapped V-belt?

No. The PIX X'tra® in this series is a moulded raw edge cogged belt. It differs from classic wrapped belts in construction, flexibility and working surface.

When should the belt be replaced?

The belt should be replaced if there are ctiming bars, obvious side surface wear, frayed edges, glazing, squealing, vibrations or repeated retensioning. The pulleys should also be in good condition, as a new belt will wear quickly in damaged grooves.

An incorrect belt specification reduces the risk of unnecessary stops, repeated replacements and troubleshooting after installation. The right combination of profile, length and construction provides better conditions for smooth running, reasonable service life and more stable power transmission in the current belt drive.

Belt operation depends on the profile, length, tension and pulley groove matching. Worn or damaged grooves can shorten belt life, while correct alignment and a clean contact surface provide more stable power transmission.

Overall rating: V-belt XPZ 655 - 10x8 MM - PIX X'tra ® is specified with profile XPZ, dimensions 10x8 MM, effective length Ld 655 mm, inner length Li 618 mm and outer length La 668 mm. The belt belongs to the PIX X'tra® series and is designed as a raw-edged, Cogged V-belts for mechanical power transmission.