Conti Synchroflex AT5 GEN III 450

Conti Synchroflex AT5 GEN III 450 – endless timing belt for precise industrial drives

When a timing belt needs to be replaced correctly, the profile, pitch length and number of teeth are the first data that must be correct. The Conti Synchroflex AT5 GEN III 450 has the AT5 GEN III profile, 5 mm tooth pitch, 450 mm pitch length and 90 teeth. This makes the product unique in terms of length and profile, while the belt width is selected separately on the product side. The belt is manufactured as an endless Conti Synchroflex PU timing belt with steel cord. The GEN III version is the reinforced high-performance construction with red high-performance polyurethane and a denser, two-filament steel cord. It should therefore be treated as a separate product series and not as the regular standard version.

Fixed specifications

• Pitch length: 450 mm
• Number of teeth: 90
• Tooth profile: AT5 GEN III
• Tooth pitch: 5 mm
• Material: cast polyurethane with steel cord
• Brand: Conti Synchroflex

The technical data below describes the part of the product that does not change when a different belt width is selected. Pitch length, tooth pitch and number of teeth remain identical for all width choices. However, the width affects the available belt cross-section width and the price calculated on the product page. Correct sizing must always take into account torque, speed, number of teeth in mesh, pulley diameters, service factor and any counter-bending.

Function of the tooth profile

The AT profile has been further developed from the classic T profile. The larger tooth volume provides a higher tooth shear strength, and the profile is designed for a favorable tooth engagement with reduced engagement shocks. This makes the AT series suitable when a drive must be compact and at the same time transmit motion precisely. Continental states that the AT profile can perform up to 50% more than a corresponding T profile, but the actual capacity always depends on width, discs, speed and load profile.

Cast polyurethane and steel cord

With the cast manufacturing method, the finished belt becomes an exact copy of a precision-machined shape. This is a major reason for the uniform tooth pitch and reproducible length. The steel cord is integrated into the polyurethane and contributes to position and angular precision. The design is suitable for synchronous drives, where a conventional elastic friction belt does not provide the desired repeatability.

What does the version designation mean?

The red GEN III construction is not just a color variant. It is developed with higher cord density and a special steel cord construction that provides increased tensile strength, better grooveing and the ability to carry higher loads. The catalog also specifies a temperature range up to +100 °C. Standard and GEN III must therefore be created and selected as separate products, even when the length and profile are the same.

Which drives is the product compatible with?

Continental cites machine tools, pu , textile machines and positioning and conveying systems as examples for this profile family. The examples describe the general area of ​​application of the profile, but do not constitute an approval for any specific installation. The final belt width and pretension must be selected based on the transmitted torque, starting and shock loads, operating time, pulley sizes, speed and the number of teeth in simultaneous engagement. For safety-critical or heavily loaded drives, an actual calculation should be made.

Disc geometry and tooth engagement

The tooth profile of the timing belt pulleys must correspond to the AT5 GEN III of the belt, and their pitch must be 5 mm. The transmission ratio is determined by the ratio of the number of teeth of the pulleys, not by the width of the belt. A larger pulley usually reduces the bending load, while a very small pulley gives more bending per revolution. The angle of engagement and the number of teeth in mesh must be sufficient for the current load.

How to avoid unnecessary wear and tear

The timing belt pulleys must be parallel and in the same plane. Even minor misalignments can cause the belt to move towards a flange and cause edge or cord damage. The belt should be installed without being twisted, sharply bent or pressed over a flange with a tool. The center distance is adjusted to achieve the calculated preload. Too high a tension increases the bearing and cord load, while too low a tension can cause tooth jumps at load peaks.

From basic width to desired width

This product line has been created with 6 mm as the base width because this is the width of the selected item and thus the SKU used for inventory control. Integer widths from 6 to 50 mm can be selected on this product page. The widths that appear as standard widths in the supplier data are marked separately in the options. The price surcharge is calculated as a percentage of the base width: doubling the width results in a surcharge of 100%. The technically necessary width should be selected according to the load and not only according to the price.

Prevention of early belt damage

Early damage is often caused by conditions surrounding the belt rather than the material itself. Bent shafts, worn tooth grooves, foreign objects and incorrect pretensioning can all shorten the service life. In the event of a belt break, the pulleys should therefore be cleaned and inspected before the new belt is fitted. Also check whether load conditions or start-stop cycles have changed since the original design.

Environmental impact and ongoing monitoring

Continental specifies a temperature range of up to +100 °C for the GEN III series. When operating close to the temperature limits, the drive must still be dimensioned according to the specific load and environmental conditions. The timing belt operates without lubrication, and oil or grease should therefore not be added to dampen noise. The polyurethane is described as resistant to aging as well as simple oils, grease and petrol and to certain acids and bases. In the case of permanent contact, cleaning chemicals or unknown media, material compatibility should be specifically clarified.

Profile and length must match

When replacing a spare part, the marking on the existing belt should be compared with the product name. Check the profile designation, pitch length, number of teeth, design and width. If the text on the belt has worn away, the number of teeth can be counted and the pitch can be assessed by measuring over several teeth. A single external length measurement is less reliable because the nominal length of the timing belt is indicated in the pitch line.

Technical questions about the product

Conti Synchroflex AT5 GEN III 450: what is the difference between tooth pitch and pitch length?

The tooth pitch is the distance from one tooth to the next and is 5 mm for this profile. The pitch length is the entire nominal circumference in the cord line and is 450 mm. When the pitch length is divided by the tooth pitch, the belt has 90 teeth.

Conti Synchroflex AT5 GEN III 450: can a wider belt always transmit twice as much?

Not necessarily. A larger width provides a more active belt cross-section and can increase the permissible load, but the drive capacity also depends on the profile, number of teeth in mesh, pulley size, speed, load factor and preload. The width should be selected by an overall calculation.

Conti Synchroflex AT5 GEN III 450: how best to store a spare timing belt?

Store the belt in a dry, clean place away from direct sunlight, ozone, strong heat or chemical fumes. It should be free from sharp bends and without heavy loads on top. Avoid hanging a small belt over a sharp hook as this can cause local deformation.

Conti Synchroflex AT5 GEN III 450: can the belt be installed by pressing it over the pulley flange?

This should be avoided. The belt should be installed by adjusting the center distance or following the correct installation procedure for the machine. Forcing it over a flange can damage the cord pullers, teeth or belt edge. After installation, the pulleys must be parallel and the pretension must be correct.

Conti Synchroflex AT5 GEN III 450: does the number of teeth change when the belt width is changed?

No. All width choices on this product page have the same pitch length of 450 mm and the same number of teeth of 90. Only the width of the belt, and thus the price and possible load capacity, changes. The width must still match the pulleys and the technical dimensioning.

Conti Synchroflex AT5 GEN III 450: why is GEN III not merged with the standard version?

GEN III has a different material construction and capacity data than the standard belt. The higher cord density, two-filament construction and high-performance polyurethane make it a separate product line, even though the pitch length and tooth profile may be identical.

Conti Synchroflex AT5 GEN III 450: when should the timing belt pulleys be replaced?

Pulleys should be evaluated if the tooth grooves are worn, sharp, crooked or damaged. A new belt on worn pulleys may have poor load distribution and short life. Also check flanges for bars and side contact and the grooves for foreign objects.

The product in brief

In summary, this is a Conti Synchroflex PU timing belt with a fixed geometry of 5 mm pitch, 90 teeth and 450 mm pitch length. The width is selected separately, but does not change the length or number of teeth. A safe replacement requires that the entire designation and the specific version match the machine documentation.