Conti Synchroflex T10 350

Conti Synchroflex T10 350 – endless metric timing belt for synchronous drives

This T10 timing belt is specified with a 350 mm pitch length and 35 teeth. The ratio between length and number of teeth is fixed: 350 mm divided by 10 mm gives exactly 35 teeth. The Conti Synchroflex T10 350 is supplied as a cast, endless PU belt, so there is no weld joint in the finished ring. The design is developed for synchronous operation and precise machine movements. This is the standard version in the specified profile. It should not be confused with a possible GEN III version or a double-sided DL belt with the same pitch length.

Product data and fixed targets

• Pitch length: 350 mm
• Number of teeth: 35
• Tooth profile: T10
• Tooth pitch: 10 mm
• Material: cast polyurethane with steel cord
• Brand: Conti Synchroflex

The list gathers the information normally used to identify a timing belt: nominal length, number of teeth, profile, material and make. It is important to read all the information together. Two belts can have the same pitch length but be incompatible if the tooth profile or tooth pitch is different. Conversely, a different width does not change the number of teeth as long as the profile and pitch length are the same.

What characterizes the T10 profile?

The trapezoidal T-geometry is a standardized solution for synchronous transmission. The teeth mesh with corresponding grooves in the timing belt pulley, so that the speed ratio is maintained without slipping. The correct pitch is crucial: a T5 belt, for example, will not fit in an AT5 pulley simply because the tooth pitch is 5 mm in both places. The shape and clearance of the tooth flanks are different.

Belt construction

With the cast manufacturing method, the finished belt becomes an exact copy of a precision-machined shape. This is a major reason for the uniform tooth pitch and reproducible length. The steel cord is integrated into the polyurethane and contributes to position and angular precision. The design is suitable for synchronous drives, where a conventional elastic friction belt does not provide the desired repeatability.

What does the version designation mean?

This item is a single-sided standard design. The teeth are located on the inside of the belt, while the back is smooth. It should not be confused with a double-sided DL version or the red GEN III series. If the machine is originally dimensioned for a specific variant, a change should only be made after a technical assessment of load, pulleys and preload.

Typical applications and sizing

The application examples in the catalogue include machine tools, main and auxiliary drives, textile machines and printing machines. This shows that the profile can be used in both power transmission and motion control. However, the specific belt must only be finally selected when the machine's torque, speed, center distance and pulley geometry are known. When simply replacing a spare part, the safest method is usually to copy the documented profile, length, design and width.

Disc geometry and tooth engagement

The tooth profile of the timing belt pulleys must correspond to the T10 of the belt, and their pitch must be 10 mm. The transmission ratio is determined by the ratio of the number of teeth of the pulleys, not by the width of the belt. A larger pulley usually reduces the bending load, while a very small pulley gives more bending per revolution. The angle of engagement and the number of teeth in mesh must be sufficient for the current load.

How to avoid unnecessary wear and tear

The belt must be able to be placed on the pulleys without force. If it can only be mounted by forcing it over a flange, the center distance or mounting procedure is incorrect. The pulley shafts must be aligned and the flanges must be smooth and undamaged. In the case of multi-shaft or counter-bent drives, the diameter and position of the rollers must be assessed separately. Correct pretensioning reduces the risk of tooth skipping without unnecessarily loading the bearings.

How the width variants work

The basic price applies to 6 mm, and the other widths are calculated with the same percentage logic as the existing PU timing belts in the webshop. Integer widths from 6 to 50 mm can be selected on this product page. A width of twice the basic width therefore costs 100% more, while a width of one and a half times the basic width gives approximately 50% extra. This price rule is a webshop calculation; it does not replace a technical dimensioning of the belt's load-bearing capacity.

Prevention of early belt damage

Early damage is often caused by conditions surrounding the belt rather than the material itself. Bent shafts, worn tooth grooves, foreign objects and incorrect pretensioning can all shorten the service life. In the event of a belt break, the pulleys should therefore be cleaned and inspected before the new belt is fitted. Also check whether load conditions or start-stop cycles have changed since the original design.

Environmental impact and ongoing monitoring

The standard material is specified for ambient temperatures from -30 °C to +80 °C. Applications close to the limits, especially below -10 °C or above +50 °C, may require special sizing. The service life is not only affected by the material, but also by load peaks, bending, pulley size, alignment and environment. Keep the drive clean and do not remove deposits with sharp tools that could damage the teeth. If the belt operates in chemically exposed areas, food environments, clean rooms or at extreme temperatures, a suitable special design should be considered.

Checking when replacing

It is not enough to compare the total circumference of a belt. The correct replacement must have the same pitch, tooth profile and number of teeth as the existing drive. The width must match the pulleys and the required capacity, and a DL or GEN III version must be identified separately. If in doubt, pictures of the marking, tooth profile and pulleys can be used as a supplement, but a documented spare part designation is best.

Technical questions about the product

Conti Synchroflex T10 350: can the belt be shortened or assembled to a different length?

No. This is a cast endless timing belt with a fixed pitch length. It can be cut to width within the available options, but the circumference and number of teeth cannot be changed. If the length needs to be changed, a different cast belt size is required.

Conti Synchroflex T10 350: how does preload affect operation?

Correct pretension keeps the teeth in stable engagement and reduces the risk of tooth jump. Too low a tension can cause impact and jump under load, while too high a tension increases the load on the cord, pulleys and bearings. The correct value must be determined based on the drive's dimensioning.

Conti Synchroflex T10 350: how best to store a spare timing belt?

Store the belt in a dry, clean place away from direct sunlight, ozone, strong heat or chemical fumes. It should be free from sharp bends and without heavy loads on top. Avoid hanging a small belt over a sharp hook as this can cause local deformation.

Conti Synchroflex T10 350: why is the number of teeth important for spare parts?

The number of teeth links the pitch of the profile to the nominal length of the belt. For this size, 35 teeth at 10 mm pitch gives a length of 350 mm. It is a simple check that often reveals faults that are not visible by a quick comparison of two loose belts.

Conti Synchroflex T10 350: can the belt be reversed on the pulleys?

The standard version is single-sided with teeth on the inside and a smooth back. It must run with the teeth in the corresponding tooth grooves; the back is not an alternative tooth side.

Conti Synchroflex T10 350: can a wider belt always transmit twice as much?

Not necessarily. A larger width provides a more active belt cross-section and can increase the permissible load, but the drive capacity also depends on the profile, number of teeth in mesh, pulley size, speed, load factor and preload. The width should be selected by an overall calculation.

Conti Synchroflex T10 350: does the number of teeth change when the belt width is changed?

No. All width choices on this product page have the same pitch length of 350 mm and the same number of teeth of 35. Only the width of the belt, and thus the price and possible load capacity, changes. The width must still match the pulleys and the technical dimensioning.

Conti Synchroflex T10 350: why can a timing belt make noise?

Noise can be caused by incorrect pretension, skewed pulleys, poor tooth profile compatibility, excessive speed, resonance or worn tooth grooves. Lubrication is not the solution. First check alignment, tension, pulley condition and whether the belt runs without abnormal side contact.

Brief summary

The product brings together the specified T10 profile and length on one side, so that the appropriate width can be selected without creating a separate item for each cut. The main technical data is 350 mm pitch length and 35 teeth. If in doubt about load or pulley compatibility, the drive should be calculated before ordering the belt.