Conti Synchroflex T2.5 265

Conti Synchroflex T2.5 265 – endless metric timing belt for synchronous drives

The Conti Synchroflex T2.5 265 is an endless, cast polyurethane timing belt with 106 teeth, 2.5 mm tooth pitch and a pitch length of 265 mm. It is intended for synchronous power transmission, where the driving and driven shafts must follow a fixed tooth ratio without the slippage known from friction-based belt drives. The pitch length is the nominal length measurement in the belt's cord line and is therefore the measurement that must be compared with the existing belt, the machine's spare part data and the installed timing belt pulleys. This is the standard version in the specified profile. It must not be confused with a possible GEN III version or a double-sided DL belt with the same pitch length.

Product data and fixed targets

• Pitch length: 265 mm
• Number of teeth: 106
• Tooth profile: T2.5
• Tooth pitch: 2.5 mm
• Material: cast polyurethane with steel cord
• Brand: Conti Synchroflex

The list gathers the information normally used to identify a timing belt: nominal length, number of teeth, profile, material and make. It is important to read all the information together. Two belts can have the same pitch length but be incompatible if the tooth profile or tooth pitch is different. Conversely, a different width does not change the number of teeth as long as the profile and pitch length are the same.

Profile, tooth pitch and engagement

The T-profile is the classic metric timing belt profile with trapezoidal teeth and is described as a standard profile according to DIN 7721. It is used for general synchronous drives, positioning tasks and solutions with significant bending. The simple and proven geometry of the profile makes it widely used, but it still needs to be matched with a T-disc with the same tooth pitch. AT, HTD and other profiles are not automatically interchangeable.

Cast polyurethane and steel cord

With the cast manufacturing method, the finished belt becomes an exact copy of a precision-machined shape. This is a major reason for the uniform tooth pitch and reproducible length. The steel cord is integrated into the polyurethane and contributes to position and angular precision. The design is suitable for synchronous drives, where a conventional elastic friction belt does not provide the desired repeatability.

What does the version designation mean?

This item is a single-sided standard design. The teeth are located on the inside of the belt, while the back is smooth. It should not be confused with a double-sided DL version or the red GEN III series. If the machine is originally dimensioned for a specific variant, a change should only be made after a technical assessment of load, pulleys and preload.

From basic width to desired width

The belt width is not written in the product name because the same pitch length is collected on one product page. The starting pu is 4 mm. Integer widths from 4 to 50 mm can be selected on this product page. The original supplier widths for this length are 4, 6, 8, 10 and 12 mm. Other intermediate sizes are offered as cut-to-size versions of the same type of timing belt sleeve when they are within the selection shown. The number of teeth, pitch length and profile do not change when the width is changed.

Areas of application

The application examples in the catalogue include precision mechanics, positioning drives, small synchronous machine movements and measuring and control equipment. This shows that the profile can be used in both power transmission and motion control. However, the specific belt must only be finally selected when the machine's torque, speed, center distance and pulley geometry are known. When simply replacing a spare part, the safest method is usually to copy the documented profile, length, design and width.

Before ordering a replacement

The product's 106 teeth provide a convenient length check. Multiplying the number of teeth by 2.5 mm gives a pitch length of 265 mm. If an existing belt has a different number of teeth, it is not the same size, even though it may look almost the same length. Also check that the teeth on the pulleys match T2.5; the same pitch number alone is not always sufficient.

Gear ratio, enclosure and tooth contact

The number of teeth on the pulleys affects both the gear ratio, deflection and how many belt teeth carry the load. A small pulley may be necessary in a compact drive, but it should not be selected without considering the minimum profile requirements and any counter deflection. Use timing belt pulleys with 2.5 mm pitch and the correct T2.5 tooth shape, and check that the flanges do not damage the belt edge.

How to avoid unnecessary wear and tear

Proper installation begins with clean, undamaged pulleys with the correct profile. Teeth and grooves should be checked for deposits, bars and wear before the new belt is fitted. The pretension should be based on the drive's calculation and should not be selected based on a random hand feel. After the initial run-in, it is a good idea to check grooveing, noise, temperature and whether the belt runs centrally.

What does belt wear indicate?

Early damage is often caused by conditions surrounding the belt rather than the material itself. Bent shafts, worn tooth grooves, foreign objects and incorrect pretensioning can all shorten the service life. In the event of a belt break, the pulleys should therefore be cleaned and inspected before the new belt is fitted. Also check whether load conditions or start-stop cycles have changed since the original design.

Temperature, media and service

The standard material is specified for ambient temperatures from -30 °C to +80 °C. Applications close to the limits, especially below -10 °C or above +50 °C, may require special sizing. The molded PU belt is maintenance-friendly and does not require lubricant. Regular visual inspection is still relevant: look for ctiming bars, frayed edges, shiny tooth flanks, foreign body impressions and abnormal side contact. Sudden changes in noise or grooveing may indicate misalignment, too low tension or worn pulleys.

Questions and answers about this timing belt

Conti Synchroflex T2.5 265: what does the pitch length of 265 mm mean?

The pitch length is the nominal length measured in the belt cord line where the steel cord tension elements are located. It is not the same as a random outer circumference measurement. For this belt, 265 mm pitch length corresponds to 106 teeth with a 2.5 mm tooth pitch.

Conti Synchroflex T2.5 265: what should be checked after the first run-in?

Check that the belt runs centrally, that there is no abnormal heat or noise, and that the edges are not constantly rubbing against the flanges. Also look for signs of too low or too high pretension. If the drive requires a re-tension check, the machine manufacturer's procedure must be followed.

Conti Synchroflex T2.5 265: can T2.5 be used on another tooth profile with the same pitch?

No, not without documented compatibility. The 2.5 mm tooth pitch describes the distance between the teeth, but the shape and clearance of the tooth flanks may differ. The belt must be used with pulleys manufactured to the T2.5 profile. Visual similarity is not sufficient documentation.

Conti Synchroflex T2.5 265: can this belt be used at high rpm?

The Conti Synchroflex series is designed for precise and fast synchronous drives, but the permissible speed depends on the profile, pulley diameter, belt width, load and peripheral speed. A high speed must therefore not be approved based on the product name alone; the drive must be calculated.

Conti Synchroflex T2.5 265: what does the steel cord mean for the function of the belt?

The steel cord tension members absorb the longitudinal tensile load and provide high longitudinal stiffness. This helps maintain pitch and position during operation. The cord must not be kinked, exposed or damaged during installation, as local damage can weaken the belt.

Conti Synchroflex T2.5 265: what is the difference between tooth pitch and pitch length?

The tooth pitch is the distance from one tooth to the next and is 2.5 mm for this profile. The pitch length is the entire nominal circumference in the cord line and is 265 mm. When the pitch length is divided by the tooth pitch, the belt has 106 teeth.

Conti Synchroflex T2.5 265: is the polyurethane oil and chemical resistant?

The standard PU is described as resistant to simple oils, grease and petrol as well as certain acids and bases. This does not mean universal chemical resistance. In the case of continuous contact, high concentrations or cleaning agents, the specific liquid, temperature and exposure time should be assessed.

The most important thing about this size

The product brings together the specified T2.5 profile and length on one side, so that the appropriate width can be selected without creating a separate item for each cut. The main technical data is 265 mm pitch length and 106 teeth. If in doubt about load or pulley compatibility, the drive should be calculated before ordering the belt.