Conti Synchroflex T5 1380

Conti Synchroflex T5 1380 – durable PU timing belt for standardized timing belt drives

The Conti Synchroflex T5 1380 combines a precise T5 tooth geometry with a molded polyurethane body and longitudinally stable steel cord tension elements. The product has 276 teeth and a pitch length of 1380 mm, which corresponds to a tooth pitch of 5 mm. The belt is used in synchronous drives where uniform movement and reproducible position are more important than the elasticity normally associated with a conventional V-belt or flat belt. This is the standard version in the specified profile. It should not be confused with a possible GEN III version or a double-sided DL belt with the same pitch length.

Fixed specifications

• Pitch length: 1380 mm
• Number of teeth: 276
• Tooth profile: T5
• Tooth pitch: 5 mm
• Material: cast polyurethane with steel cord
• Brand: Conti Synchroflex

The technical data below describes the part of the product that does not change when a different belt width is selected. Pitch length, tooth pitch and number of teeth remain identical for all width choices. However, the width affects the available belt cross-section width and the price calculated on the product page. Correct sizing must always take into account torque, speed, number of teeth in mesh, pulley diameters, service factor and any counter-bending.

What characterizes the T5 profile?

The trapezoidal T-geometry is a standardized solution for synchronous transmission. The teeth mesh with corresponding grooves in the timing belt pulley, so that the speed ratio is maintained without slipping. The correct pitch is crucial: a T5 belt, for example, will not fit in an AT5 pulley simply because the tooth pitch is 5 mm in both places. The shape and clearance of the tooth flanks are different.

PU body and longitudinally stable traction elements

The endless PU construction combines low dead weight with high longitudinal rigidity. The steel cord tension elements are cast into the belt and are not intended to be exposed, damaged or sharply broken during installation. The wear resistance of the polyurethane and the strong bond to the cord are central to the belt's lifespan. Correct handling is therefore just as important as the correct choice of profile and length.

The execution must be correctly identified

The standard version is selected when the supplier's article data does not specify GEN III or DL. This is an important product distinction, because different versions can share both profile and length. Therefore, on this product page, it is the standard version that is described. The belt width can be selected, but the basic construction and tooth geometry are not changed.

Where is this profile used?

The application examples in the catalogue include office machines, household appliances, positioning drives and control drives. This shows that the profile can be used in both power transmission and motion control. However, the specific belt must only be finally selected when the machine's torque, speed, centre distance and pulley geometry are known. When simply replacing a spare part, the safest method is usually to copy the documented profile, length, design and width.

Selection of discs for the profile

A belt of the correct length can still function poorly if the pulleys have the wrong profile, are worn or are misaligned. Therefore, check the tooth grooves, flanges, shaft alignment and the number of teeth on the pulleys. For T5, the nominal tooth pitch is 5 mm. The fixed tooth mesh makes the gear ratio reproducible, but only when the belt has sufficient wrap and does not run with constant side pressure.

Practical advice for installation

The timing belt pulleys must be parallel and in the same plane. Even minor misalignments can cause the belt to move towards a flange and cause edge or cord damage. The belt should be installed without being twisted, sharply bent or pressed over a flange with a tool. The center distance is adjusted to achieve the calculated preload. Too high a tension increases the bearing and cord load, while too low a tension can cause tooth jumps at load peaks.

The belt width is selected on the product page

The basic price applies to 6 mm, and the other widths are calculated with the same percentage logic as the existing PU timing belts in the webshop. Integer widths from 6 to 50 mm can be selected on this product page. A width of twice the basic width therefore costs 100% more, while a width of one and a half times the basic width gives approximately 50% extra. This price rule is a webshop calculation; it does not replace a technical dimensioning of the belt's load-bearing capacity.

Wear patterns and troubleshooting

Troubleshooting should start with pu location of the damage. Edge wear is typically associated with grooveing and alignment, while tooth skipping can be associated with too low tension, load peaks or too few teeth in mesh. Ctiming bars on the back can be caused by too small rollers, back bending or environmental influences. Do not simply replace the belt without also finding the mechanical cause.

Temperature, media and service

The standard material is specified for ambient temperatures from -30 °C to +80 °C. Applications close to the limits, especially below -10 °C or above +50 °C, may require special sizing. The service life is not only affected by the material, but also by load peaks, bending, pulley size, alignment and environment. Keep the drive clean and do not remove deposits with sharp tools that could damage the teeth. If the belt operates in chemically exposed areas, food environments, clean rooms or at extreme temperatures, a suitable special design should be considered.

How to identify the correct replacement belt

It is not enough to compare the total circumference of a belt. The correct replacement must have the same pitch, tooth profile and number of teeth as the existing drive. The width must match the pulleys and the required capacity, and a DL or GEN III version must be identified separately. If in doubt, pictures of the marking, tooth profile and pulleys can be used as a supplement, but a documented spare part designation is best.

Frequently Asked Questions

Conti Synchroflex T5 1380: can the belt be shortened or assembled to a different length?

No. This is a cast endless timing belt with a fixed pitch length. It can be cut to width within the available options, but the circumference and number of teeth cannot be changed. If the length needs to be changed, a different cast belt size is required.

Conti Synchroflex T5 1380: what is the difference between T5 and a GEN III belt?

This product is the standard version. GEN III is a separate reinforced series with red high-performance PU and denser, two-filament steel cord. The same profile and length therefore do not mean that the products are identical.

Conti Synchroflex T5 1380: what does the pitch length of 1380 mm mean?

The pitch length is the nominal length measured in the belt cord line where the steel cord tension elements are located. It is not the same as a random outer circumference measurement. For this belt, 1380 mm pitch length corresponds to 276 teeth with 5 mm tooth pitch.

Conti Synchroflex T5 1380: can a wider belt always transmit twice as much?

Not necessarily. A larger width provides a more active belt cross-section and can increase the permissible load, but the drive capacity also depends on the profile, number of teeth in mesh, pulley size, speed, load factor and preload. The width should be selected by an overall calculation.

Conti Synchroflex T5 1380: can T5 be used on a different tooth profile with the same pitch?

No, not without documented compatibility. The 5 mm tooth pitch describes the distance between the teeth, but the shape and clearance of the tooth flanks may differ. The belt must be used with pulleys manufactured for the T5 profile. Visual similarity is not sufficient documentation.

Conti Synchroflex T5 1380: does the number of teeth change when the belt width is changed?

No. All width choices on this product page have the same pitch length of 1380 mm and the same number of teeth of 276. Only the width of the belt, and thus the price and possible load capacity, changes. The width must still match the pulleys and the technical dimensioning.

Conti Synchroflex T5 1380: can the belt be installed by pressing it over the pulley flange?

This should be avoided. The belt should be installed by adjusting the center distance or following the correct installation procedure for the machine. Forcing it over a flange can damage the cord pullers, teeth or belt edge. After installation, the pulleys must be parallel and the pretension must be correct.

Conti Synchroflex T5 1380: why is 6 mm chosen as the basic width?

6 mm is the width of the supplier item whose SKU is used as the main product's stock reference. Other widths are handled as choices under the same product because they are cut from the same type of timing belt sleeve. The base width also determines the percentage-based pricing in the webshop.

Summary

In summary, this is a Conti Synchroflex PU timing belt with a fixed geometry of 5 mm pitch, 276 teeth and 1380 mm pitch length. The width is selected separately, but does not change the length or number of teeth. A safe replacement requires that the entire designation and the specific version match the machine documentation.