Conti Synchroflex AT3 GEN III 267

Conti Synchroflex AT3 GEN III 267 – dimensionally stable PU timing belt for positioning and transmission

With 89 teeth distributed over a pitch length of 267 mm, the Conti Synchroflex AT3 GEN III 267 is designed for precise transmission of rotation, stroke and position. The belt is cast endlessly in PU and has integrated steel cord tension elements that stabilize the length during normal operation. The nominal tooth pitch is 3 mm and the tooth profile must match the profile of the pulleys precisely. It is not sufficient for another belt to have approximately the same length or width. The GEN III version is the reinforced high-performance construction with red high-performance polyurethane and denser, two-filament steel cord. It should therefore be treated as a separate product series and not as the usual standard version.

Fixed specifications

• Pitch length: 267 mm
• Number of teeth: 89
• Tooth profile: AT3 GEN III
• Tooth pitch: 3 mm
• Material: cast polyurethane with steel cord
• Brand: Conti Synchroflex

The list gathers the information normally used to identify a timing belt: nominal length, number of teeth, profile, material and make. It is important to read all the information together. Two belts can have the same pitch length but be incompatible if the tooth profile or tooth pitch is different. Conversely, a different width does not change the number of teeth as long as the profile and pitch length are the same.

Function of the tooth profile

The AT profile has been further developed from the classic T profile. The larger tooth volume provides a higher tooth shear strength, and the profile is designed for a favorable tooth engagement with reduced engagement shocks. This makes the AT series suitable when a drive must be compact and at the same time transmit motion precisely. Continental states that the AT profile can perform up to 50% more than a corresponding T profile, but the actual capacity always depends on width, discs, speed and load profile.

Cast polyurethane and steel cord

With the cast manufacturing method, the finished belt becomes an exact copy of a precision-machined shape. This is a major reason for the uniform tooth pitch and reproducible length. The steel cord is integrated into the polyurethane and contributes to position and angular precision. The design is suitable for synchronous drives, where a conventional elastic friction belt does not provide the desired repeatability.

The specific product version

GEN III is the reinforced high-performance version of the Conti Synchroflex series. The construction uses red high-performance polyurethane, more densely packed steel cord tension elements and a two-filament construction with balanced S and Z cords. Continental states up to 25% higher power transmission than the corresponding AT or ATP standard series. GEN III can use the standard profile timing belt pulleys, but the belt still needs to be dimensioned for the specific drive.

Choosing belt width

This product line has been created with 6 mm as the base width because this is the width of the selected item and thus the SKU used for inventory control. Integer widths from 6 to 50 mm can be selected on this product page. The widths that appear as standard widths in the supplier data are marked separately in the options. The price surcharge is calculated as a percentage of the base width: doubling the width results in a surcharge of 100%. The technically necessary width should be selected according to the load and not only according to the price.

Relevant machine tasks

The profile series is used in practice for tasks such as small power drives, handling equipment, compact positioning axes and light synchronous feeds. Common to these machines is the need for a fixed transmission ratio and controlled tooth meshing. A timing belt can transmit both force and position, but the capacity cannot be assessed based on length alone. Width, profile version, wrap angle and load cycle are among the data that must be included in the selection.

How to identify the correct replacement belt

It is not enough to compare the total circumference of a belt. The correct replacement must have the same pitch, tooth profile and number of teeth as the existing drive. The width must match the pulleys and the required capacity, and a DL or GEN III version must be identified separately. If in doubt, pictures of the marking, tooth profile and pulleys can be used as a supplement, but a documented spare part designation is best.

Timing belt pulleys and transmission ratios

The number of teeth on the pulleys affects both the gear ratio, deflection and how many belt teeth carry the load. A small pulley may be necessary in a compact drive, but it should not be selected without considering the minimum profile requirements and any counter deflection. Use timing belt pulleys with 3 mm pitch and the correct AT3 GEN III tooth shape, and check that the flanges do not damage the belt edge.

How to avoid unnecessary wear and tear

Proper installation begins with clean, undamaged pulleys with the correct profile. Teeth and grooves should be checked for deposits, bars and wear before the new belt is fitted. The pretension should be based on the drive's calculation and should not be selected based on a random hand feel. After the initial run-in, it is a good idea to check grooveing, noise, temperature and whether the belt runs centrally.

Wear patterns and troubleshooting

A properly running timing belt should move smoothly without continuous contact against one flange. Regularly check the teeth for deformation, the back for ctiming bars and the edges for frayed areas. Abnormal noise or heat can be an early sign of incorrect tension or pulley failure. A systematic check of pulleys and belt is more effective than trying to hide symptoms with lubricant.

Operating environment and maintenance

Continental specifies a temperature range of up to +100 °C for the GEN III series. When operating close to the temperature limits, the drive must still be dimensioned according to the specific load and environmental conditions. The timing belt operates without lubrication, and oil or grease should therefore not be added to dampen noise. The polyurethane is described as resistant to aging as well as simple oils, grease and petrol and to certain acids and bases. In the case of permanent contact, cleaning chemicals or unknown media, material compatibility should be specifically clarified.

Answers to typical questions

Conti Synchroflex AT3 GEN III 267: how to check if the length is correct?

Count the teeth and check the pitch. 89 teeth times 3 mm gives 267 mm pitch length. Then compare the profile and design with the marking or the machine parts list. A measurement around the outside of the belt alone is not accurate enough.

Conti Synchroflex AT3 GEN III 267: how does preload affect operation?

Correct pretension keeps the teeth in stable engagement and reduces the risk of tooth jump. Too low a tension can cause impact and jump under load, while too high a tension increases the load on the cord, pulleys and bearings. The correct value must be determined based on the drive's dimensioning.

Conti Synchroflex AT3 GEN III 267: why is GEN III not merged with the standard version?

GEN III has a different material construction and capacity data than the standard belt. The higher cord density, two-filament construction and high-performance polyurethane make it a separate product line, even though the pitch length and tooth profile may be identical.

Conti Synchroflex AT3 GEN III 267: what happens if the discs are not aligned?

Misalignment can cause the belt to wander towards a flange, causing edge pressure, heat and wear damage. It can also affect tooth engagement and reduce service life. Check both the parallelism of the shafts and the alignment of the pulleys.

Conti Synchroflex AT3 GEN III 267: does the number of teeth change when the belt width is changed?

No. All width choices on this product page have the same pitch length of 267 mm and the same number of teeth of 89. Only the width of the belt, and thus the price and possible load capacity, changes. The width must still match the pulleys and the technical dimensioning.

Conti Synchroflex AT3 GEN III 267: what does the pitch length of 267 mm mean?

The pitch length is the nominal length measured in the belt cord line where the steel cord tension members are located. It is not the same as a random outside circumference measurement. For this belt, 267 mm pitch length corresponds to 89 teeth with 3 mm tooth pitch.

Conti Synchroflex AT3 GEN III 267: are the standard widths the only possible widths?

The documented supplier widths for this size include 6, 8, 10, 12, 16, 20, 25, 32 and 50 mm. The product page may also show intermediate sizes as cut widths when they are within the allowed range. This does not change the tooth profile or length, but the price is calculated based on the base width.

The product in brief

The product brings together the specified AT3 GEN III profile and length on one side, so that the appropriate width can be selected without creating a separate item for each cut. The main technical data is 267 mm pitch length and 89 teeth. If in doubt about load or pulley compatibility, the drive should be calculated before ordering the belt.