Conti Synchroflex T2 256

Conti Synchroflex T2 256 – classic PU timing belt with trapezoidal teeth

When a timing belt needs to be replaced correctly, the profile, pitch length and number of teeth are the first data that must be correct. The Conti Synchroflex T2 256 has a T2 profile, 2 mm tooth pitch, 256 mm pitch length and 128 teeth. This makes the product unique in terms of length and profile, while the belt width is selected separately on the product page. The belt is manufactured as an endless Conti Synchroflex PU timing belt with steel cord. This is the standard version in the specified profile. It must not be confused with a possible GEN III version or a double-sided DL belt with the same pitch length.

Dimensions, profile and number of teeth

• Pitch length: 256 mm
• Number of teeth: 128
• Tooth profile: T2
• Tooth pitch: 2 mm
• Material: cast polyurethane with steel cord
• Brand: Conti Synchroflex

The technical data below describes the part of the product that does not change when a different belt width is selected. Pitch length, tooth pitch and number of teeth remain identical for all width choices. However, the width affects the available belt cross-section width and the price calculated on the product page. Correct sizing must always take into account torque, speed, number of teeth in mesh, pulley diameters, service factor and any counter-bending.

Why the correct profile is crucial

The T-profile is the classic metric timing belt profile with trapezoidal teeth and is described as a standard profile according to DIN 7721. It is used for general synchronous drives, positioning tasks and solutions with significant bending. The simple and proven geometry of the profile makes it widely used, but it still needs to be matched with a T-disc with the same tooth pitch. AT, HTD and other profiles are not automatically interchangeable.

PU body and longitudinally stable traction elements

The endless PU construction combines low dead weight with high longitudinal rigidity. The steel cord tension elements are cast into the belt and are not intended to be exposed, damaged or sharply broken during installation. The wear resistance of the polyurethane and the strong bond to the cord are central to the belt's lifespan. Correct handling is therefore just as important as the correct choice of profile and length.

The construction behind this variant

This item is a single-sided standard design. The teeth are located on the inside of the belt, while the back is smooth. It should not be confused with a double-sided DL version or the red GEN III series. If the machine is originally dimensioned for a specific variant, a change should only be made after a technical assessment of load, pulleys and preload.

Before ordering a replacement

It is not enough to compare the total circumference of a belt. The correct replacement must have the same pitch, tooth profile and number of teeth as the existing drive. The width must match the pulleys and the required capacity, and a DL or GEN III version must be identified separately. If in doubt, pictures of the marking, tooth profile and pulleys can be used as a supplement, but a documented spare part designation is best.

Typical applications and sizing

The profile series is used in practice for tasks such as precision mechanics, positioning drives, small synchronous mechanisms and compact machine drives. Common to these machines is the need for a fixed transmission ratio and controlled tooth engagement. A timing belt can transmit both force and position, but the capacity cannot be assessed based on length alone. Width, profile version, wrap angle and load cycle are among the data that must be included in the selection.

Choosing belt width

This product line has been created with 100 mm as the base width because this is the width of the selected item and thus the SKU used for inventory control. Since the source data only contains this size in 100 mm, the product has been created with 100 mm as the only documented width. The widths that appear as standard widths in the supplier data are marked separately in the options. The price surcharge is calculated as a percentage of the base width: doubling the width results in a surcharge of 100%. The technically necessary width must be selected according to the load and not only according to the price.

Gear ratio, enclosure and tooth contact

The number of teeth on the pulleys affects both gear ratio, deflection and how many belt teeth carry the load. A small pulley may be necessary in a compact drive, but it should not be selected without considering the minimum profile requirements and any counter deflection. Use timing belt pulleys with 2 mm pitch and the correct T2 tooth shape, and check that the flanges do not damage the belt edge.

Practical advice for installation

When installing, the cord pullers must be protected against kinks and local pressure damage. The belt must not be pinched with pliers or a screwdriver, and it should not be folded sharply. Check that the pulleys have the same pitch and profile as the belt and that they are not worn out. A stable drive is achieved through the right combination of alignment, wrapping and calculated pretension.

Maintenance-free does not mean control-free

The standard material is specified for ambient temperatures from -30 °C to +80 °C. Applications close to the limits, especially below -10 °C or above +50 °C, may require special sizing. The service life is not only affected by the material, but also by load peaks, bending, pulley size, alignment and environment. Keep the drive clean and do not remove deposits with sharp tools that could damage the teeth. If the belt operates in chemically exposed areas, food environments, clean rooms or at extreme temperatures, a suitable special design should be considered.

Wear patterns and troubleshooting

Uniform light polishing of the tooth flanks may be normal, but localised spalling, ctiming baring or severe wear should be investigated. Wear on one edge often indicates misalignment or persistent flange contact. Damage to tooth tips may be due to incorrect profile, foreign bodies or inadequate engagement. If cord becomes visible or the belt has a sharp break, it should not continue in service without assessment.

Frequently Asked Questions

Conti Synchroflex T2 256: when should the timing belt pulleys be replaced?

Pulleys should be evaluated if the tooth grooves are worn, sharp, crooked or damaged. A new belt on worn pulleys may have poor load distribution and short life. Also check flanges for bars and side contact and the grooves for foreign objects.

Conti Synchroflex T2 256: can the width be measured with a regular caliper?

Yes, the belt width can usually be measured directly on the flat back or between clean, undamaged edges. However, the width is only one part of the identification. The profile, pitch length, number of teeth and any DL or GEN III version must also be correct.

Conti Synchroflex T2 256: why is the number of teeth important for spare parts?

The number of teeth links the pitch of the profile to the nominal length of the belt. For this size, 128 teeth at 2 mm pitch gives a length of 256 mm. It is a simple check that often reveals faults that are not visible by a quick comparison of two loose belts.

Conti Synchroflex T2 256: can this belt be used at high speeds?

The Conti Synchroflex series is designed for precise and fast synchronous drives, but the permissible speed depends on the profile, pulley diameter, belt width, load and peripheral speed. A high speed must therefore not be approved based on the product name alone; the drive must be calculated.

Conti Synchroflex T2 256: what does the steel cord mean for the function of the belt?

The steel cord tension members absorb the longitudinal tensile load and provide high longitudinal stiffness. This helps maintain pitch and position during operation. The cord must not be kinked, exposed or damaged during installation, as local damage can weaken the belt.

Conti Synchroflex T2 256: why can a timing belt make noise?

Noise can be caused by incorrect pretension, skewed pulleys, poor tooth profile compatibility, excessive speed, resonance or worn tooth grooves. Lubrication is not the solution. First check alignment, tension, pulley condition and whether the belt runs without abnormal side contact.

Conti Synchroflex T2 256: can the belt run with counter-bending?

The possibility depends on the profile, cord design, the diameter of the rollers and the specific belt routing. Counter-bending increases the bending load and must be included in the dimensioning. A roller on the belt back must have sufficient diameter and be positioned so that tooth engagement and grooveing are not impaired.

Conti Synchroflex T2 256: why is 100 mm chosen as the basic width?

100 mm is the width of the supplier item whose SKU is used as the main product's stock reference. Other widths are handled as choices under the same product because they are cut from the same type of timing belt sleeve. The base width also determines the percentage-based price calculation in the webshop.

Conclusion

The product brings together the specified T2 profile and length on one side, so that the appropriate width can be selected without creating a separate item for each cut. The main technical data is 256 mm pitch length and 128 teeth. If in doubt about load or pulley compatibility, the drive should be calculated before ordering the belt.