Conti Synchroflex AT10 1400

Conti Synchroflex AT10 1400 – durable PU timing belt with stable tooth pitch

The Conti Synchroflex AT10 1400 combines a precise AT10 tooth geometry with a molded polyurethane body and longitudinally stable steel cord tension elements. The product has 140 teeth and a pitch length of 1400 mm, which corresponds to a tooth pitch of 10 mm. The belt is used in synchronous drives where uniform movement and reproducible position are more important than the elasticity normally associated with a conventional V-belt or flat belt. This is the standard version in the specified profile. It must not be confused with a possible GEN III version or a double-sided DL belt with the same pitch length.

The most important product data

• Pitch length: 1400 mm
• Number of teeth: 140
• Tooth profile: AT10
• Tooth pitch: 10 mm
• Material: cast polyurethane with steel cord
• Brand: Conti Synchroflex

These specifications can be used as a check against the marking on the old belt or against the machine's spare parts list. The pitch length is not necessarily the same as a measurement across the outside of the belt, and the number of teeth is therefore often the safest additional check. If in doubt, both the belt and timing belt pulleys should be examined before ordering a replacement.

Why the correct profile is crucial

In a synchronous belt drive, the movement is transmitted through the tooth flanks. The geometry of the AT profile is therefore crucial for both load distribution, noise level and position accuracy. A correct AT pulley supports the teeth according to the profile to which they are cast. If the pulley's tooth shape or pitch deviates, the load can be concentrated at a few pu and cause abnormal wear, even though the belt can apparently be mounted.

How the Conti Synchroflex belt is constructed

The belt body consists of wear-resistant polyurethane, which encloses high-strength steel cord. The materials each have their own function: PU forms the teeth and protects the belt against mechanical wear, while the cord tensioning elements provide high longitudinal stiffness and limit post-elongation. Continental describes the design as maintenance-friendly and lubrication-free. This does not mean that the drive can be ignored; pulleys, alignment and pretension should still be checked.

The specific product version

This item is a single-sided standard design. The teeth are located on the inside of the belt, while the back is smooth. It should not be confused with a double-sided DL version or the red GEN III series. If the machine is originally dimensioned for a specific variant, a change should only be made after a technical assessment of load, pulleys and preload.

Which drives is the product compatible with?

The profile series is used in practice for tasks such as construction machinery, pu , paper machines, compressors, compactors, textile machines and roller conveyor drives. Common to these machines is the need for a fixed transmission ratio and controlled tooth engagement. A timing belt can transmit both force and position, but the capacity cannot be assessed based on length alone. Width, profile version, wrap angle and load cycle are among the data that must be included in the selection.

Temperature, media and service

The standard material is specified for ambient temperatures from -30 °C to +80 °C. Applications close to the limits, especially below -10 °C or above +50 °C, may require special dimensioning. The timing belt operates without lubrication, and oil or grease should therefore not be added to dampen noise. The polyurethane is described as resistant to aging as well as simple oils, grease and petrol and to certain acids and bases. In the case of permanent contact, cleaning chemicals or unknown media, material compatibility should be specifically clarified.

Width selection and price calculation

The basic price applies to 16 mm, and the other widths are calculated with the same percentage logic as the existing PU timing belts in the webshop. Integer widths from 16 to 50 mm can be selected on this product page. A width of twice the basic width therefore costs 100% more, while a width of one and a half times the basic width gives approximately a 50% surcharge. This price rule is a webshop calculation; it does not replace a technical dimensioning of the belt's load-bearing capacity.

Disc geometry and tooth engagement

The number of teeth on the pulleys affects both the gear ratio, deflection and how many belt teeth carry the load. A small pulley may be necessary in a compact drive, but it should not be selected without considering the minimum profile requirements and any counter deflection. Use timing belt pulleys with 10 mm pitch and the correct AT10 tooth shape, and check that the flanges do not damage the belt edge.

Pre-tensioning and disc alignment

The timing belt pulleys must be parallel and in the same plane. Even minor misalignments can cause the belt to move towards a flange and cause edge or cord damage. The belt should be installed without being twisted, sharply bent or pressed over a flange with a tool. The center distance is adjusted to achieve the calculated preload. Too high a tension increases the bearing and cord load, while too low a tension can cause tooth jumps at load peaks.

Prevention of early belt damage

Early damage is often caused by conditions surrounding the belt rather than the material itself. Bent shafts, worn tooth grooves, foreign objects and incorrect pretensioning can all shorten the service life. In the event of a belt break, the pulleys should therefore be cleaned and inspected before the new belt is fitted. Also check whether load conditions or start-stop cycles have changed since the original design.

Profile and length must match

It is not enough to compare the total circumference of a belt. The correct replacement must have the same pitch, tooth profile and number of teeth as the existing drive. The width must match the pulleys and the required capacity, and a DL or GEN III version must be identified separately. If in doubt, pictures of the marking, tooth profile and pulleys can be used as a supplement, but a documented spare part designation is best.

Frequently Asked Questions

Conti Synchroflex AT10 1400: can the belt be reversed on the pulleys?

The standard version is single-sided with teeth on the inside and a smooth back. It must run with the teeth in the corresponding tooth grooves; the back is not an alternative tooth side.

Is the Conti Synchroflex AT10 1400 welded?

No. The Conti Synchroflex series is manufactured as cast, endless timing belts. The belt therefore does not have a welded joint around the circumference. The cast process provides a uniform tooth pitch around the entire belt and a strong bond between the polyurethane and the cast steel cord tension elements.

Conti Synchroflex AT10 1400: can this belt be used at high rpm?

The Conti Synchroflex series is designed for precise and fast synchronous drives, but the permissible speed depends on the profile, pulley diameter, belt width, load and peripheral speed. A high speed must therefore not be approved based on the product name alone; the drive must be calculated.

Conti Synchroflex AT10 1400: why is the number of teeth important for spare parts?

The number of teeth links the pitch of the profile to the nominal length of the belt. For this size, 140 teeth at 10 mm pitch gives a length of 1400 mm. It is a simple check that often reveals faults that are not visible by a quick comparison of two loose belts.

Conti Synchroflex AT10 1400: how does preload affect operation?

Correct pretension keeps the teeth in stable engagement and reduces the risk of tooth jump. Too low a tension can cause impact and jump under load, while too high a tension increases the load on the cord, pulleys and bearings. The correct value must be determined based on the drive's dimensioning.

Conti Synchroflex AT10 1400: can AT10 be used on a different tooth profile with the same pitch?

No, not without documented compatibility. The 10 mm tooth pitch describes the distance between the teeth, but the shape and clearance of the tooth flanks may differ. The belt must be used with pulleys manufactured to the AT10 profile. Visual similarity is not sufficient documentation.

Conti Synchroflex AT10 1400: are the standard widths the only possible widths?

The documented supplier widths for this size include 16, 20, 25, 32 and 50 mm. The product page may also show intermediate sizes as cut widths when they are within the allowed range. This does not change the tooth profile or length, but the price is calculated based on the base width.

Conti Synchroflex AT10 1400: can an old V-belt be directly replaced by this timing belt?

No. A timing belt requires timing belt pulleys with the correct profile and pitch, while a V-belt works by friction in V-grooves. A conversion therefore requires new pulleys and a dimensioning of the entire transmission. The product is intended as a timing belt, not as a universal replacement.

The most important thing about this size

Conti Synchroflex AT10 1400 is the correct size when the drive requires AT10, 1400 mm pitch length and 140 teeth. The belt is cast endless in PU with steel cord and must be used with timing belt pulleys that match the profile. Choose the width according to the technical load and always check the design, alignment and pretension before commissioning.