Conti Synchroflex AT10 780

Conti Synchroflex AT10 780 – durable PU timing belt with stable tooth pitch

With 78 teeth spread over a pitch length of 780 mm, the Conti Synchroflex AT10 780 is designed for precise transmission of rotation, timing and position. The belt is cast endlessly in PU and has integrated steel cord tension elements that stabilize the length during normal operation. The nominal tooth pitch is 10 mm and the tooth profile must match the profile of the pulleys exactly. It is not sufficient for another belt to have approximately the same length or width. This is the standard version in the specified profile. It must not be confused with a possible GEN III version or a double-sided DL belt with the same pitch length.

Product data and fixed targets

• Pitch length: 780 mm
• Number of teeth: 78
• Tooth profile: AT10
• Tooth pitch: 10 mm
• Material: cast polyurethane with steel cord
• Brand: Conti Synchroflex

The technical data below describes the part of the product that does not change when a different belt width is selected. Pitch length, tooth pitch and number of teeth remain identical for all width choices. However, the width affects the available belt cross-section width and the price calculated on the product page. Correct sizing must always take into account torque, speed, number of teeth in mesh, pulley diameters, service factor and any counter-bending.

Why the correct profile is crucial

In a synchronous belt drive, the movement is transmitted through the tooth flanks. The geometry of the AT profile is therefore crucial for both load distribution, noise level and position accuracy. A correct AT pulley supports the teeth according to the profile to which they are cast. If the pulley's tooth shape or pitch deviates, the load can be concentrated at a few pu and cause abnormal wear, even though the belt can apparently be mounted.

PU body and longitudinally stable traction elements

The belt body consists of wear-resistant polyurethane, which encloses high-strength steel cord. The materials each have their own function: PU forms the teeth and protects the belt against mechanical wear, while the cord tensioning elements provide high longitudinal stiffness and limit post-elongation. Continental describes the design as maintenance-friendly and lubrication-free. This does not mean that the drive can be ignored; pulleys, alignment and pretension should still be checked.

The construction behind this variant

The product is the regular Conti Synchroflex standard version in the specified profile. Standard and GEN III may have the same pitch length and number of teeth, but they are different product series with different material construction and capacity data. The same applies to a DL belt, which has teeth on both sides. When reordering, the entire profile designation should therefore be checked, not just the length.

Profile and length must match

When replacing a spare part, the marking on the existing belt should be compared with the product name. Check the profile designation, pitch length, number of teeth, design and width. If the text on the belt has worn away, the number of teeth can be counted and the pitch can be assessed by measuring over several teeth. A single external length measurement is less reliable because the nominal length of the timing belt is indicated in the pitch line.

Where is this profile used?

The profile series is used in practice for tasks such as construction machinery, pu , paper machines, compressors, compactors, textile machines and roller conveyor drives. Common to these machines is the need for a fixed transmission ratio and controlled tooth engagement. A timing belt can transmit both force and position, but the capacity cannot be assessed based on length alone. Width, profile version, wrap angle and load cycle are among the data that must be included in the selection.

From basic width to desired width

The belt width is not written in the product name because the same pitch length is collected on one product page. The starting pu is 16 mm. Integer widths from 16 to 50 mm can be selected on this product page. The original supplier widths for this length are 16, 20, 25, 32 and 50 mm. Other intermediate sizes are offered as cut-to-sizes of the same type of timing belt sleeve when they are within the selection shown. The number of teeth, pitch length and profile do not change when the width is changed.

Disc geometry and tooth engagement

A belt of the correct length can still function poorly if the pulleys have the wrong profile, are worn or are misaligned. Therefore, check the tooth grooves, flanges, shaft alignment and the number of teeth on the pulleys. For AT10, the nominal tooth pitch is 10 mm. The fixed tooth mesh makes the gear ratio reproducible, but only when the belt has sufficient wrap and does not run with constant side pressure.

Splice, alignment and pre-tensioning

The timing belt pulleys must be parallel and in the same plane. Even minor misalignments can cause the belt to move towards a flange and cause edge or cord damage. The belt should be installed without being twisted, sharply bent or pressed over a flange with a tool. The center distance is adjusted to achieve the calculated preload. Too high a tension increases the bearing and cord load, while too low a tension can cause tooth jumps at load peaks.

Temperature, media and service

The standard material is specified for ambient temperatures from -30 °C to +80 °C. Applications close to the limits, especially below -10 °C or above +50 °C, may require special dimensioning. The timing belt operates without lubrication, and oil or grease should therefore not be added to dampen noise. The polyurethane is described as resistant to aging as well as simple oils, grease and petrol and to certain acids and bases. In the case of permanent contact, cleaning chemicals or unknown media, material compatibility should be specifically clarified.

Checking teeth, back and edges

A properly running timing belt should move smoothly without continuous contact against one flange. Regularly check the teeth for deformation, the back for ctiming bars and the edges for frayed areas. Abnormal noise or heat can be an early sign of incorrect tension or pulley failure. A systematic check of pulleys and belt is more effective than trying to hide symptoms with lubricant.

Technical questions about the product

Conti Synchroflex AT10 780 with 16 mm basic width: how to check if the length is correct?

Count the teeth and check the pitch. 78 teeth times 10 mm gives 780 mm pitch length. Then compare the profile and design with the marking or the machine's spare parts list. A measurement around the outside of the belt alone is not accurate enough.

Conti Synchroflex AT10 780 with 16 mm basic width: can the belt be installed by pressing it over the flange of the pulley?

This should be avoided. The belt should be installed by adjusting the center distance or following the correct installation procedure for the machine. Forcing it over a flange can damage the cord pullers, teeth or belt edge. After installation, the pulleys must be parallel and the pretension must be correct.

Conti Synchroflex AT10 780 with 16 mm basic width: can the belt be used for precise positioning?

The tooth engagement provides a positive, synchronous transmission without the normal slippage of a friction belt. This makes the profile relevant for positioning tasks, but the achievable accuracy also depends on the quality of the pulleys, shaft play, belt pretension, load and the overall machine design.

Conti Synchroflex AT10 780 with 16 mm basic width: what should be checked after the first run-in?

Check that the belt runs centrally, that there is no abnormal heat or noise, and that the edges are not constantly rubbing against the flanges. Also look for signs of too low or too high pretension. If the drive requires a re-tension check, the machine manufacturer's procedure must be followed.

Conti Synchroflex AT10 780 with 16 mm base width: is the polyurethane oil and chemical resistant?

The standard PU is described as resistant to simple oils, grease and petrol as well as certain acids and bases. This does not mean universal chemical resistance. In the case of continuous contact, high concentrations or cleaning agents, the specific liquid, temperature and exposure time should be assessed.

Conti Synchroflex AT10 780 with 16 mm basic width: why was 16 mm chosen as the basic width?

16 mm is the width of the supplier item whose SKU is used as the main product's stock reference. Other widths are handled as choices under the same product because they are cut from the same type of timing belt sleeve. The base width also determines the percentage-based pricing in the webshop.

Conti Synchroflex AT10 780 with 16 mm basic width: when should the timing belt pulleys be replaced?

Pulleys should be evaluated if the tooth grooves are worn, sharp, crooked or damaged. A new belt on worn pulleys may have poor load distribution and short life. Also check flanges for bars and side contact and the grooves for foreign objects.

The product in brief

The product brings together the specified AT10 profile and length on one side, so that the appropriate width can be selected without creating a separate item for each cut. The main technical data is 780 mm pitch length and 78 teeth. If in doubt about load or pulley compatibility, the drive should be calculated before ordering the belt.