Conti Synchroflex AT10 GEN III 1720

Conti Synchroflex AT10 GEN III 1720 – precise PU timing belt for synchronous power transmission

The Conti Synchroflex AT10 GEN III 1720 combines a precise AT10 GEN III tooth geometry with a molded polyurethane body and longitudinally stable steel cord tension elements. The product has 172 teeth and a 1720 mm pitch length, which corresponds to a tooth pitch of 10 mm. The belt is used in synchronous drives where uniform movement and reproducible position are more important than the elasticity normally associated with a conventional V-belt or flat belt. The GEN III version is the reinforced high-performance construction with red high-performance polyurethane and a denser, two-filament steel cord. It should therefore be treated as a separate product series and not as the usual standard version.

Key technical data

• Pitch length: 1720 mm
• Number of teeth: 172
• Tooth profile: AT10 GEN III
• Tooth pitch: 10 mm
• Material: cast polyurethane with steel cord
• Brand: Conti Synchroflex

The technical data below describes the part of the product that does not change when a different belt width is selected. Pitch length, tooth pitch and number of teeth remain identical for all width choices. However, the width affects the available belt cross-section width and the price calculated on the product page. Correct sizing must always take into account torque, speed, number of teeth in mesh, pulley diameters, service factor and any counter-bending.

Why the correct profile is crucial

In a synchronous belt drive, the movement is transmitted through the tooth flanks. The geometry of the AT profile is therefore crucial for both load distribution, noise level and position accuracy. A correct AT pulley supports the teeth according to the profile to which they are cast. If the pulley's tooth shape or pitch deviates, the load can be concentrated at a few pu and cause abnormal wear, even though the belt can apparently be mounted.

PU body and longitudinally stable traction elements

With the cast manufacturing method, the finished belt becomes an exact copy of a precision-machined shape. This is a major reason for the uniform tooth pitch and reproducible length. The steel cord is integrated into the polyurethane and contributes to position and angular precision. The design is suitable for synchronous drives, where a conventional elastic friction belt does not provide the desired repeatability.

Standard, GEN III or DL ​​– this version

The red GEN III construction is not just a color variant. It is developed with higher cord density and a special steel cord construction that provides increased tensile strength, better grooveing and the ability to carry higher loads. The catalog also specifies a temperature range up to +100 °C. Standard and GEN III must therefore be created and selected as separate products, even when the length and profile are the same.

Areas of application

The profile series is used in practice for tasks such as construction machinery, pu , paper machines, compressors, compactors, textile machines and roller conveyor drives. Common to these machines is the need for a fixed transmission ratio and controlled tooth engagement. A timing belt can transmit both force and position, but the capacity cannot be assessed based on length alone. Width, profile version, wrap angle and load cycle are among the data that must be included in the selection.

Operating environment and maintenance

Continental specifies a temperature range of up to +100 °C for the GEN III series. When operating close to the temperature limits, the drive must still be dimensioned according to the specific load and environmental conditions. The timing belt operates without lubrication, and oil or grease should therefore not be added to dampen noise. The polyurethane is described as resistant to aging as well as simple oils, grease and petrol and to certain acids and bases. In the case of permanent contact, cleaning chemicals or unknown media, material compatibility should be specifically clarified.

Choosing belt width

This product line has been created with 16 mm as the base width because this is the width of the selected item and thus the SKU used for inventory control. Integer widths from 16 to 50 mm can be selected on this product page. The widths that appear as standard widths in the supplier data are marked separately in the options. The price surcharge is calculated as a percentage of the base width: doubling the width results in a surcharge of 100%. The technically necessary width should be selected according to the load and not only according to the price.

Disc geometry and tooth engagement

The tooth profile of the timing belt pulleys must correspond to the AT10 GEN III of the belt, and their pitch must be 10 mm. The transmission ratio is determined by the ratio of the number of teeth of the pulleys, not by the width of the belt. A larger pulley usually reduces the bending load, while a very small pulley gives more bending per revolution. The angle of engagement and the number of teeth in mesh must be sufficient for the current load.

How to avoid unnecessary wear and tear

The timing belt pulleys must be parallel and in the same plane. Even minor misalignments can cause the belt to move towards a flange and cause edge or cord damage. The belt should be installed without being twisted, sharply bent or pressed over a flange with a tool. The center distance is adjusted to achieve the calculated preload. Too high a tension increases the bearing and cord load, while too low a tension can cause tooth jumps at load peaks.

Signs of improper operation

A properly running timing belt should move smoothly without continuous contact against one flange. Regularly check the teeth for deformation, the back for ctiming bars and the edges for frayed areas. Abnormal noise or heat can be an early sign of incorrect tension or pulley failure. A systematic check of pulleys and belt is more effective than trying to hide symptoms with lubricant.

Profile and length must match

The product's 172 teeth provide a convenient length check. Multiplying the number of teeth by 10 mm gives a pitch length of 1720 mm. If an existing belt has a different number of teeth, it is not the same size, even though it may look almost the same length. Also check that the teeth on the pulleys match the AT10 GEN III; the same pitch number alone is not always sufficient.

Answers to typical questions

Conti Synchroflex AT10 GEN III 1720: what does the steel cord mean for the function of the belt?

The steel cord tension members absorb the longitudinal tensile load and provide high longitudinal stiffness. This helps maintain pitch and position during operation. The cord must not be kinked, exposed or damaged during installation, as local damage can weaken the belt.

Conti Synchroflex AT10 GEN III 1720: what is the difference between tooth pitch and pitch length?

The tooth pitch is the distance from one tooth to the next and is 10 mm for this profile. The pitch length is the entire nominal circumference in the cord line and is 1720 mm. When the pitch length is divided by the tooth pitch, the belt has 172 teeth.

Conti Synchroflex AT10 GEN III 1720: what is the difference between the AT10 GEN III and a GEN III belt?

This product is already GEN III. The reinforced version features high-performance PU and denser, two-filament steel cord construction and is a separate product line from the standard belt.

Conti Synchroflex AT10 GEN III 1720: can GEN III run on standard AT10 discs?

Continental states that the GEN III version can be used on standard timing belt pulleys for the corresponding AT10 profile. However, the pulleys must be in good condition and the drive must be dimensioned for the load you want to utilize.

Conti Synchroflex AT10 GEN III 1720: why is GEN III not merged with the standard version?

GEN III has a different material construction and capacity data than the standard belt. The higher cord density, two-filament construction and high-performance polyurethane make it a separate product line, even though the pitch length and tooth profile may be identical.

Conti Synchroflex AT10 GEN III 1720: can the belt be used for precise positioning?

The tooth engagement provides a positive, synchronous transmission without the normal slippage of a friction belt. This makes the profile relevant for positioning tasks, but the achievable accuracy also depends on the quality of the pulleys, shaft play, belt pretension, load and the overall machine design.

Conti Synchroflex AT10 GEN III 1720: can the belt be shortened or assembled to a different length?

No. This is a cast endless timing belt with a fixed pitch length. It can be cut to width within the available options, but the circumference and number of teeth cannot be changed. If the length needs to be changed, a different cast belt size is required.

The most important thing about this size

Conti Synchroflex AT10 GEN III 1720 is the correct size when the drive requires AT10 GEN III, 1720 mm pitch length and 172 teeth. The belt is cast endless in PU with steel cord and must be used with timing belt pulleys that match the profile. Choose the width according to the technical load and always check the design, alignment and pretension before commissioning.