Conti Synchroflex AT10 GEN III 1800

Conti Synchroflex AT10 GEN III 1800 – compact timing belt for precise motion transmission

This AT10 GEN III timing belt is specified with a pitch length of 1800 mm and 180 teeth. The ratio between length and number of teeth is fixed: 1800 mm divided by 10 mm gives exactly 180 teeth. The Conti Synchroflex AT10 GEN III 1800 is supplied as a cast, endless PU belt, so that there is no weld joint in the finished ring. The design is developed for synchronous operation and precise machine movements. The GEN III version is the reinforced high-performance design with red high-performance polyurethane and denser, two-filament steel cord. It should therefore be treated as a separate product series and not as the regular standard version.

Product data and fixed targets

• Pitch length: 1800 mm
• Number of teeth: 180
• Tooth profile: AT10 GEN III
• Tooth pitch: 10 mm
• Material: cast polyurethane with steel cord
• Brand: Conti Synchroflex

These specifications can be used as a check against the marking on the old belt or against the machine's spare parts list. The pitch length is not necessarily the same as a measurement across the outside of the belt, and the number of teeth is therefore often the safest additional check. If in doubt, both the belt and timing belt pulleys should be examined before ordering a replacement.

How tooth geometry works

The AT profile has been further developed from the classic T profile. The larger tooth volume provides a higher tooth shear strength, and the profile is designed for a favorable tooth engagement with reduced engagement shocks. This makes the AT series suitable when a drive must be compact and at the same time transmit motion precisely. Continental states that the AT profile can perform up to 50% more than a corresponding T profile, but the actual capacity always depends on width, discs, speed and load profile.

Cast polyurethane and steel cord

Conti Synchroflex is manufactured by casting, where the polyurethane is precisely shaped to the tool's tooth geometry around the embedded steel cord tension elements. The casting process provides high pitch accuracy over the entire circumference of the belt and a strong connection between PU and cord. The finished timing belt is endless and therefore has no welded joints. The polyurethane provides a wear-resistant tooth and back surface, while the steel cord takes the longitudinal tensile load.

Standard, GEN III or DL ​​– this version

In the GEN III series, both the polyurethane and the tension body are optimized for higher performance. The tighter cord packing can increase the permissible tensile load, and the balanced two-filament construction is designed to reduce flange friction and improve belt running. Continental states that existing standard AT or ATP pulleys can be used with the corresponding GEN III profile. However, the remaining dimensioning of the drive still needs to be checked.

Areas of application

The profile series is used in practice for tasks such as construction machinery, pu , paper machines, compressors, compactors, textile machines and roller conveyor drives. Common to these machines is the need for a fixed transmission ratio and controlled tooth engagement. A timing belt can transmit both force and position, but the capacity cannot be assessed based on length alone. Width, profile version, wrap angle and load cycle are among the data that must be included in the selection.

Width selection and price calculation

The basic price applies to 16 mm, and the other widths are calculated with the same percentage logic as the existing PU timing belts in the webshop. Integer widths from 16 to 50 mm can be selected on this product page. A width of twice the basic width therefore costs 100% more, while a width of one and a half times the basic width gives approximately a 50% surcharge. This price rule is a webshop calculation; it does not replace a technical dimensioning of the belt's load-bearing capacity.

Disc geometry and tooth engagement

A belt of the correct length can still function poorly if the pulleys have the wrong profile, are worn or are misaligned. Therefore, check the tooth grooves, flanges, shaft alignment and the number of teeth on the pulleys. For AT10 GEN III, the nominal tooth pitch is 10 mm. The fixed tooth mesh makes the gear ratio reproducible, but only when the belt has sufficient wrap and does not run with constant side pressure.

How to avoid unnecessary wear and tear

The belt must be able to be placed on the pulleys without force. If it can only be mounted by forcing it over a flange, the center distance or mounting procedure is incorrect. The pulley shafts must be aligned and the flanges must be smooth and undamaged. In the case of multi-shaft or counter-bent drives, the diameter and position of the rollers must be assessed separately. Correct pretensioning reduces the risk of tooth skipping without unnecessarily loading the bearings.

Before ordering a replacement

When replacing a spare part, the marking on the existing belt should be compared with the product name. Check the profile designation, pitch length, number of teeth, design and width. If the text on the belt has worn away, the number of teeth can be counted and the pitch can be assessed by measuring over several teeth. A single external length measurement is less reliable because the nominal length of the timing belt is indicated in the pitch line.

What does belt wear indicate?

Uniform light polishing of the tooth flanks may be normal, but localised spalling, ctiming baring or severe wear should be investigated. Wear on one edge often indicates misalignment or persistent flange contact. Damage to tooth tips may be due to incorrect profile, foreign bodies or inadequate engagement. If cord becomes visible or the belt has a sharp break, it should not continue in service without assessment.

Environmental impact and ongoing monitoring

Continental specifies a temperature range of up to +100 °C for the GEN III series. When operating close to the temperature limits, the drive must still be dimensioned according to the specific load and environmental conditions. The cast PU belt is maintenance-friendly and does not require lubricant. Regular visual inspection is still relevant: look for ctiming bars, frayed edges, shiny tooth flanks, foreign body impressions and abnormal side contact. Sudden changes in noise or grooveing can be signs of misalignment, too low tension or worn pulleys.

Frequently Asked Questions

Conti Synchroflex AT10 GEN III 1800: how to best store a spare timing belt?

Store the belt in a dry, clean place away from direct sunlight, ozone, strong heat or chemical fumes. It should be free from sharp bends and without heavy loads on top. Avoid hanging a small belt over a sharp hook as this can cause local deformation.

Is the Conti Synchroflex AT10 GEN III 1800 welded?

No. The Conti Synchroflex series is manufactured as cast, endless timing belts. The belt therefore does not have a welded joint around the circumference. The cast process provides a uniform tooth pitch around the entire belt and a strong bond between the polyurethane and the cast steel cord tension elements.

Conti Synchroflex AT10 GEN III 1800: can the belt be installed by pressing it over the flange of the pulley?

This should be avoided. The belt should be installed by adjusting the center distance or following the correct installation procedure for the machine. Forcing it over a flange can damage the cord pullers, teeth or belt edge. After installation, the pulleys must be parallel and the pretension must be correct.

Conti Synchroflex AT10 GEN III 1800: can the belt run with counter-bending?

The possibility depends on the profile, cord design, the diameter of the rollers and the specific belt routing. Counter-bending increases the bending load and must be included in the dimensioning. A roller on the belt back must have sufficient diameter and be positioned so that tooth engagement and grooveing are not impaired.

Conti Synchroflex AT10 GEN III 1800: why is 16 mm chosen as the basic width?

16 mm is the width of the supplier item whose SKU is used as the main product's stock reference. Other widths are handled as choices under the same product because they are cut from the same type of timing belt sleeve. The base width also determines the percentage-based pricing in the webshop.

Conti Synchroflex AT10 GEN III 1800: when should the timing belt pulleys be replaced?

Pulleys should be evaluated if the tooth grooves are worn, sharp, crooked or damaged. A new belt on worn pulleys may have poor load distribution and short life. Also check flanges for bars and side contact and the grooves for foreign objects.

Conti Synchroflex AT10 GEN III 1800: why is GEN III not merged with the standard version?

GEN III has a different material construction and capacity data than the standard belt. The higher cord density, two-filament construction and high-performance polyurethane make it a separate product line, even though the pitch length and tooth profile may be identical.

The most important thing about this size

Conti Synchroflex AT10 GEN III 1800 is the correct size when the drive requires AT10 GEN III, 1800 mm pitch length and 180 teeth. The belt is cast endless in PU with steel cord and must be used with timing belt pulleys that match the profile. Choose the width according to the technical load and always check the design, alignment and pretension before commissioning.