Conti Synchroflex T5 1075

Conti Synchroflex T5 1075 – precise T-profile timing belt in cast polyurethane

Conti Synchroflex T5 1075 is an endless, cast polyurethane timing belt with 215 teeth, 5 mm tooth pitch and a pitch length of 1075 mm. It is intended for synchronous power transmission, where the driving and driven shafts must follow a fixed tooth ratio without the slippage known from friction-based belt drives. The pitch length is the nominal length measurement in the belt's cord line and is therefore the measurement that must be compared with the existing belt, the machine's spare part data and the installed timing belt pulleys. This is the standard version in the specified profile. It must not be confused with a possible GEN III version or a double-sided DL belt with the same pitch length.

Fixed specifications

• Pitch length: 1075 mm
• Number of teeth: 215
• Tooth profile: T5
• Tooth pitch: 5 mm
• Material: cast polyurethane with steel cord
• Brand: Conti Synchroflex

The list gathers the information normally used to identify a timing belt: nominal length, number of teeth, profile, material and make. It is important to read all the information together. Two belts can have the same pitch length but be incompatible if the tooth profile or tooth pitch is different. Conversely, a different width does not change the number of teeth as long as the profile and pitch length are the same.

Profile, tooth pitch and engagement

The T-profile is the classic metric timing belt profile with trapezoidal teeth and is described as a standard profile according to DIN 7721. It is used for general synchronous drives, positioning tasks and solutions with significant bending. The simple and proven geometry of the profile makes it widely used, but it still needs to be matched with a T-disc with the same tooth pitch. AT, HTD and other profiles are not automatically interchangeable.

Materials and endless manufacturing

The endless PU construction combines low dead weight with high longitudinal rigidity. The steel cord tension elements are cast into the belt and are not intended to be exposed, damaged or sharply broken during installation. The wear resistance of the polyurethane and the strong bond to the cord are central to the belt's lifespan. Correct handling is therefore just as important as the correct choice of profile and length.

What does the version designation mean?

The product is the regular Conti Synchroflex standard version in the specified profile. Standard and GEN III may have the same pitch length and number of teeth, but they are different product series with different material construction and capacity data. The same applies to a DL belt, which has teeth on both sides. When reordering, the entire profile designation should therefore be checked, not just the length.

Areas of application

The profile series is used in practice for tasks such as office machines, household appliances, positioning drives and control drives. Common to these machines is the need for a fixed transmission ratio and controlled tooth meshing. A timing belt can transmit both force and position, but the capacity cannot be assessed based on length alone. Width, profile version, wrap angle and load cycle are among the data that must be included in the selection.

Operating environment and maintenance

The standard material is specified for ambient temperatures from -30 °C to +80 °C. Applications close to the limits, especially below -10 °C or above +50 °C, may require special sizing. The service life is not only affected by the material, but also by load peaks, bending, pulley size, alignment and environment. Keep the drive clean and do not remove deposits with sharp tools that could damage the teeth. If the belt operates in chemically exposed areas, food environments, clean rooms or at extreme temperatures, a suitable special design should be considered.

Choosing belt width

The basic price applies to 6 mm, and the other widths are calculated with the same percentage logic as the existing PU timing belts in the webshop. Integer widths from 6 to 50 mm can be selected on this product page. A width of twice the basic width therefore costs 100% more, while a width of one and a half times the basic width gives approximately 50% extra. This price rule is a webshop calculation; it does not replace a technical dimensioning of the belt's load-bearing capacity.

Timing belt pulleys and transmission ratios

A belt of the correct length can still function poorly if the pulleys have the wrong profile, are worn or are misaligned. Therefore, check the tooth grooves, flanges, shaft alignment and the number of teeth on the pulleys. For T5, the nominal tooth pitch is 5 mm. The fixed tooth mesh makes the gear ratio reproducible, but only when the belt has sufficient wrap and does not run with constant side pressure.

Pre-tensioning and disc alignment

When installing, the cord pullers must be protected against kinks and local pressure damage. The belt must not be pinched with pliers or a screwdriver, and it should not be folded sharply. Check that the pulleys have the same pitch and profile as the belt and that they are not worn out. A stable drive is achieved through the right combination of alignment, wrapping and calculated pretension.

Wear patterns and troubleshooting

Uniform light polishing of the tooth flanks may be normal, but localised spalling, ctiming baring or severe wear should be investigated. Wear on one edge often indicates misalignment or persistent flange contact. Damage to tooth tips may be due to incorrect profile, foreign bodies or inadequate engagement. If cord becomes visible or the belt has a sharp break, it should not continue in service without assessment.

Before ordering a replacement

The product's 215 teeth provide a convenient length check. Multiplying the number of teeth by 5 mm gives a pitch length of 1075 mm. If an existing belt has a different number of teeth, it is not the same size, even though it may look almost the same length. Also check that the teeth on the pulleys match the T5; the same pitch number alone is not always sufficient.

Practical questions before ordering

Conti Synchroflex T5 1075: what is the difference between tooth pitch and pitch length?

The tooth pitch is the distance from one tooth to the next and is 5 mm for this profile. The pitch length is the entire nominal circumference in the cord line and is 1075 mm. When the pitch length is divided by the tooth pitch, the belt has 215 teeth.

Conti Synchroflex T5 1075: what temperature can the belt work at?

The standard version is specified for ambient temperatures from -30 °C to +80 °C. At temperatures below -10 °C or above +50 °C, adapted sizing may be required.

How many teeth does the Conti Synchroflex T5 1075 have?

The belt has 215 teeth. The number of teeth is calculated by dividing the pitch length of 1075 mm by the tooth pitch of 5 mm. The result is 215, and this number can be used as an additional check when identifying an existing belt. A different number of teeth means a different pitch length.

Conti Synchroflex T5 1075: what is the difference between T5 and a GEN III belt?

This product is the standard version. GEN III is a separate reinforced series with red high-performance PU and denser, two-filament steel cord. The same profile and length therefore do not mean that the products are identical.

Conti Synchroflex T5 1075: can the belt be installed by pressing it over the flange of the pulley?

This should be avoided. The belt should be installed by adjusting the center distance or following the correct installation procedure for the machine. Forcing it over a flange can damage the cord pullers, teeth or belt edge. After installation, the pulleys must be parallel and the pretension must be correct.

Conti Synchroflex T5 1075: why can a timing belt make noise?

Noise can be caused by incorrect pretension, skewed pulleys, poor tooth profile compatibility, excessive speed, resonance or worn tooth grooves. Lubrication is not the solution. First check alignment, tension, pulley condition and whether the belt runs without abnormal side contact.

Conti Synchroflex T5 1075: what does the pitch length of 1075 mm mean?

The pitch length is the nominal length measured in the belt cord line where the steel cord tension members are located. It is not the same as a random outside circumference measurement. For this belt, 1075 mm pitch length corresponds to 215 teeth with 5 mm tooth pitch.

Conti Synchroflex T5 1075: can the width be measured with a regular caliper?

Yes, the belt width can usually be measured directly on the flat back or between clean, undamaged edges. However, the width is only one part of the identification. The profile, pitch length, number of teeth and any DL or GEN III version must also be correct.

Conclusion

Conti Synchroflex T5 1075 is the correct size when the drive requires T5, 1075 mm pitch length and 215 teeth. The belt is cast endless in PU with steel cord and must be used with timing belt pulleys that match the profile. Choose the width according to the technical load and always check the design, alignment and pretension before commissioning.