Conti Synchroflex T2 140

Conti Synchroflex T2 140 – endless metric timing belt for synchronous drives

With 70 teeth spread over a pitch length of 140 mm, the Conti Synchroflex T2 140 is designed for precise transmission of rotation, timing and position. The belt is cast endlessly in PU and has integrated steel cord tension elements that stabilize the length during normal operation. The nominal tooth pitch is 2 mm and the tooth profile must match the profile of the pulleys exactly. It is not sufficient for another belt to have approximately the same length or width. This is the standard version in the specified profile. It must not be confused with a possible GEN III version or a double-sided DL belt with the same pitch length.

The most important product data

• Pitch length: 140 mm
• Number of teeth: 70
• Tooth profile: T2
• Tooth pitch: 2 mm
• Material: cast polyurethane with steel cord
• Brand: Conti Synchroflex

The technical data below describes the part of the product that does not change when a different belt width is selected. Pitch length, tooth pitch and number of teeth remain identical for all width choices. However, the width affects the available belt cross-section width and the price calculated on the product page. Correct sizing must always take into account torque, speed, number of teeth in mesh, pulley diameters, service factor and any counter-bending.

Profile, tooth pitch and engagement

As a classic metric profile, the T-series is used in many machines where reliable synchronous movement is important. The tooth shape is trapezoidal, and the number in the profile designation indicates the tooth pitch in millimeters. The correct washer must therefore both have the same pitch and be manufactured for the T-profile. The wrong profile can lead to poor engagement, noise and rapid wear.

PU body and longitudinally stable traction elements

The endless PU construction combines low dead weight with high longitudinal rigidity. The steel cord tension elements are cast into the belt and are not intended to be exposed, damaged or sharply broken during installation. The wear resistance of the polyurethane and the strong bond to the cord are central to the belt's lifespan. Correct handling is therefore just as important as the correct choice of profile and length.

The construction behind this variant

This item is a single-sided standard design. The teeth are located on the inside of the belt, while the back is smooth. It should not be confused with a double-sided DL version or the red GEN III series. If the machine is originally dimensioned for a specific variant, a change should only be made after a technical assessment of load, pulleys and preload.

Choosing belt width

The basic price applies to 4 mm, and the other widths are calculated with the same percentage logic as the existing PU timing belts in the webshop. Integer widths from 4 to 50 mm can be selected on this product page. A width of twice the basic width therefore costs 100% more, while a width of one and a half times the basic width gives approximately 50% extra. This price rule is a webshop calculation; it does not replace a technical dimensioning of the belt's load-bearing capacity.

Which drives is the product compatible with?

The profile series is used in practice for tasks such as precision mechanics, positioning drives, small synchronous mechanisms and compact machine drives. Common to these machines is the need for a fixed transmission ratio and controlled tooth engagement. A timing belt can transmit both force and position, but the capacity cannot be assessed based on length alone. Width, profile version, wrap angle and load cycle are among the data that must be included in the selection.

Before ordering a replacement

It is not enough to compare the total circumference of a belt. The correct replacement must have the same pitch, tooth profile and number of teeth as the existing drive. The width must match the pulleys and the required capacity, and a DL or GEN III version must be identified separately. If in doubt, pictures of the marking, tooth profile and pulleys can be used as a supplement, but a documented spare part designation is best.

Gear ratio, enclosure and tooth contact

The pulleys and belt should be considered as a single tooth engagement. Correct T2 geometry ensures that the load is distributed over the tooth flanks instead of being concentrated on tooth tips or edges. The drive ratio is selected by the number of teeth on the pulleys, while the belt's 70 teeth and 140 mm pitch length determine the required combination of pulleys and center distance. When changing the drive, the geometry should be calculated.

Practical advice for installation

The timing belt pulleys must be parallel and in the same plane. Even minor misalignments can cause the belt to move towards a flange and cause edge or cord damage. The belt should be installed without being twisted, sharply bent or pressed over a flange with a tool. The center distance is adjusted to achieve the calculated preload. Too high a tension increases the bearing and cord load, while too low a tension can cause tooth jumps at load peaks.

Checking teeth, back and edges

Troubleshooting should start with pu location of the damage. Edge wear is typically associated with grooveing and alignment, while tooth skipping can be associated with too low tension, load peaks or too few teeth in mesh. Ctiming bars on the back can be caused by too small rollers, back bending or environmental influences. Do not simply replace the belt without also finding the mechanical cause.

Environmental impact and ongoing monitoring

The standard material is specified for ambient temperatures from -30 °C to +80 °C. Applications close to the limits, especially below -10 °C or above +50 °C, may require special sizing. The service life is not only affected by the material, but also by load peaks, bending, pulley size, alignment and environment. Keep the drive clean and do not remove deposits with sharp tools that could damage the teeth. If the belt operates in chemically exposed areas, food environments, clean rooms or at extreme temperatures, a suitable special design should be considered.

Technical questions about the product

Conti Synchroflex T2 140: what is the difference between T2 and a GEN III belt?

This product is the standard version. GEN III is a separate reinforced series with red high-performance PU and denser, two-filament steel cord. The same profile and length therefore do not mean that the products are identical.

Conti Synchroflex T2 140: are the standard widths the only possible widths?

The documented supplier widths for this size include 4, 6 and 10 mm. The product page may also show intermediate sizes as cut widths when they are within the allowed range. This does not change the tooth profile or length, but the price is calculated based on the base width.

Conti Synchroflex T2 140: what is the difference between tooth pitch and pitch length?

The tooth pitch is the distance from one tooth to the next and is 2 mm for this profile. The pitch length is the entire nominal circumference in the cord line and is 140 mm. When the pitch length is divided by the tooth pitch, the belt has 70 teeth.

Conti Synchroflex T2 140: can this belt be used at high rpm?

The Conti Synchroflex series is designed for precise and fast synchronous drives, but the permissible speed depends on the profile, pulley diameter, belt width, load and peripheral speed. A high speed must therefore not be approved based on the product name alone; the drive must be calculated.

Conti Synchroflex T2 140: can the width be measured with a regular caliper?

Yes, the belt width can usually be measured directly on the flat back or between clean, undamaged edges. However, the width is only one part of the identification. The profile, pitch length, number of teeth and any DL or GEN III version must also be correct.

Conti Synchroflex T2 140: what should be checked after the first run-in?

Check that the belt runs centrally, that there is no abnormal heat or noise, and that the edges are not constantly rubbing against the flanges. Also look for signs of too low or too high pretension. If the drive requires a re-tension check, the machine manufacturer's procedure must be followed.

Conti Synchroflex T2 140: does the number of teeth change when the belt width is changed?

No. All width choices on this product page have the same pitch length of 140 mm and the same number of teeth of 70. Only the width of the belt, and thus the price and possible load capacity, changes. The width must still match the pulleys and the technical dimensioning.

The product in brief

Conti Synchroflex T2 140 is the correct size when the drive requires T2, 140 mm pitch length and 70 teeth. The belt is cast endless in PU with steel cord and must be used with timing belt pulleys that match the profile. Choose the width according to the technical load and always check the design, alignment and pretension before commissioning.