PU timing belt AT3 417 - Conti® Synchroflex

Conti Synchroflex AT3 417 – precise PU timing belt for synchronous power transmission

Conti Synchroflex AT3 417 combines a precise AT3 tooth geometry with a molded polyurethane body and longitudinally stable steel cord tension elements. The product has 139 teeth and a pitch length of 417 mm, which corresponds to a tooth pitch of 3 mm. The belt is used in synchronous drives where uniform movement and reproducible position are more important than the elasticity normally associated with a conventional V-belt or flat belt. This is the standard version in the specified profile. It should not be confused with a possible GEN III version or a double-sided DL belt with the same pitch length.

Dimensions, profile and number of teeth

• Pitch length: 417 mm
• Number of teeth: 139
• Tooth profile: AT3
• Tooth pitch: 3 mm
• Material: cast polyurethane with steel cord
• Brand: Conti Synchroflex

The technical data below describes the part of the product that does not change when a different belt width is selected. Pitch length, tooth pitch and number of teeth remain identical for all width choices. However, the width affects the available belt cross-section width and the price calculated on the product page. Correct sizing must always take into account torque, speed, number of teeth in mesh, pulley diameters, service factor and any counter-bending.

Why the correct profile is crucial

The metric AT geometry has trapezoidal teeth with a larger tooth volume than the standard T profile. The purpose is to distribute the load advantageously in the tooth mesh and achieve higher tooth strength without making the drive unnecessarily large. The profile requires suitable AT timing belt pulleys with the same pitch; a visual similarity to other profiles is not evidence of compatibility.

PU body and longitudinally stable traction elements

The endless PU construction combines low dead weight with high longitudinal rigidity. The steel cord tension elements are cast into the belt and are not intended to be exposed, damaged or sharply broken during installation. The wear resistance of the polyurethane and the strong bond to the cord are central to the belt's lifespan. Correct handling is therefore just as important as the correct choice of profile and length.

The execution must be correctly identified

The product is the regular Conti Synchroflex standard version in the specified profile. Standard and GEN III may have the same pitch length and number of teeth, but they are different product series with different material construction and capacity data. The same applies to a DL belt, which has teeth on both sides. When reordering, the entire profile designation should therefore be checked, not just the length.

Which drives is the product compatible with?

Continental cites small power drives, handling equipment, compact positioning axes and light synchronous drives as examples for this profile family. The examples describe the general application area of ​​the profile, but are not an approval for any specific installation. The final belt width and pretension must be selected based on the transmitted torque, starting and shock loads, operating time, pulley sizes, speed and the number of teeth in simultaneous engagement. For safety-critical or heavily loaded drives, an actual calculation should be made.

Environmental impact and ongoing monitoring

The standard material is specified for ambient temperatures from -30 °C to +80 °C. Applications close to the limits, especially below -10 °C or above +50 °C, may require special dimensioning. The timing belt operates without lubrication, and oil or grease should therefore not be added to dampen noise. The polyurethane is described as resistant to aging as well as simple oils, grease and petrol and to certain acids and bases. In the case of permanent contact, cleaning chemicals or unknown media, material compatibility should be specifically clarified.

Choosing belt width

The basic price applies to 6 mm, and the other widths are calculated with the same percentage logic as the existing PU timing belts in the webshop. Integer widths from 6 to 50 mm can be selected on this product page. A width of twice the basic width therefore costs 100% more, while a width of one and a half times the basic width gives approximately 50% extra. This price rule is a webshop calculation; it does not replace a technical dimensioning of the belt's load-bearing capacity.

The discs are part of the overall solution

The pulleys and belt should be considered as a single tooth engagement. Correct AT3 geometry ensures that the load is distributed over the tooth flanks rather than concentrated on tooth tips or edges. The drive ratio is selected by the number of teeth on the pulleys, while the belt's 139 teeth and 417 mm pitch length determine the required combination of pulleys and center distance. When changing the drive, the geometry should be calculated.

Pre-tensioning and disc alignment

The timing belt pulleys must be parallel and in the same plane. Even minor misalignments can cause the belt to move towards a flange and cause edge or cord damage. The belt should be installed without being twisted, sharply bent or pressed over a flange with a tool. The center distance is adjusted to achieve the calculated preload. Too high a tension increases the bearing and cord load, while too low a tension can cause tooth jumps at load peaks.

Signs of improper operation

Early damage is often caused by conditions surrounding the belt rather than the material itself. Bent shafts, worn tooth grooves, foreign objects and incorrect pretensioning can all shorten the service life. In the event of a belt break, the pulleys should therefore be cleaned and inspected before the new belt is fitted. Also check whether load conditions or start-stop cycles have changed since the original design.

Profile and length must match

When replacing a spare part, the marking on the existing belt should be compared with the product name. Check the profile designation, pitch length, number of teeth, design and width. If the text on the belt has worn away, the number of teeth can be counted and the pitch can be assessed by measuring over several teeth. A single external length measurement is less reliable because the nominal length of the timing belt is indicated in the pitch line.

Practical questions before ordering

Conti Synchroflex AT3 417: what does the pitch length of 417 mm mean?

The pitch length is the nominal length measured in the belt cord line where the steel cord tension members are located. It is not the same as a random outside circumference measurement. For this belt, 417 mm pitch length corresponds to 139 teeth with 3 mm tooth pitch.

Conti Synchroflex AT3 417: why is the number of teeth important for spare parts?

The number of teeth links the pitch of the profile to the nominal length of the belt. For this size, 139 teeth at 3 mm pitch gives a length of 417 mm. It is a simple check that often reveals faults that are not visible by a quick comparison of two loose belts.

Conti Synchroflex AT3 417: can this belt be used at high speeds?

The Conti Synchroflex series is designed for precise and fast synchronous drives, but the permissible speed depends on the profile, pulley diameter, belt width, load and peripheral speed. A high speed must therefore not be approved based on the product name alone; the drive must be calculated.

Conti Synchroflex AT3 417: can the belt be turned upside down on the pulleys?

The standard version is single-sided with teeth on the inside and a smooth back. It must run with the teeth in the corresponding tooth grooves; the back is not an alternative tooth side.

Conti Synchroflex AT3 417: why can a timing belt make noise?

Noise can be caused by incorrect pretension, skewed pulleys, poor tooth profile compatibility, excessive speed, resonance or worn tooth grooves. Lubrication is not the solution. First check alignment, tension, pulley condition and whether the belt runs without abnormal side contact.

Conti Synchroflex AT3 417: can the belt be shortened or assembled to a different length?

No. This is a cast endless timing belt with a fixed pitch length. It can be cut to width within the available options, but the circumference and number of teeth cannot be changed. If the length needs to be changed, a different cast belt size is required.

Conti Synchroflex AT3 417: can the width be measured with a regular caliper?

Yes, the belt width can usually be measured directly on the flat back or between clean, undamaged edges. However, the width is only one part of the identification. The profile, pitch length, number of teeth and any DL or GEN III version must also be correct.

Conti Synchroflex AT3 417: are the standard widths the only possible widths?

The documented supplier widths for this size include 6, 8, 10, 12, 16, 20, 25, 32 and 50 mm. The product page may also show intermediate sizes as cut widths when they are within the allowed range. This does not change the tooth profile or length, but the price is calculated based on the base width.

Brief summary

In summary, this is a Conti Synchroflex PU timing belt with a fixed geometry of 3 mm pitch, 139 teeth and 417 mm pitch length. The width is selected separately, but does not change the length or number of teeth. A safe replacement requires that the entire designation and the specific version match the machine documentation.